User manual MAXDATA PRO 6000T

[. . . ] User Guide - Multimedia Notebook Computer 37 38 Contents NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 SHIPPING CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] - Despite operating it correctly, the computer is not functioning properly. - The computer has been dropped or damaged. · Cleaning Never apply cleaning agents directly to the computer. Never use volatile (petroleum distillates) or scouring cleaning agents. 45 Shipping Contents SHIPPING CONTENTS Before you begin installing your notebook, make sure that all components are present. If any item listed in the shipping contents is missing from your computer package, please contact your dealer immediately. · Notebook · Battery · Utility CD · Power adapter · Power cable · User guide · CD or DVD-ROM drive (built in) · Modem cable Please retain the original packaging in case you need to send the device in for repairs or upgrades. 46 Preparation PREPARATION Before first using the computer, make sure you are familiar with the individual components of your system. Slide the catch (1) to the right and open the display. 1 1 11 8 10 9 8 7 (1) (2) (3) 3 (4) (5) 4 (6) (7) 5 6 (8) (9) (10) (11) 2 ON/OFF button Catch Display Hot Keys Status LEDs Keyboard TouchPad Stereo loudspeakers Power LED Battery LED Scroll buttons Fig. 2 47 Preparation INSERTING THE BATTERY The battery is included in the notebook's shipping contents. Take the new battery out of its packaging. Now slide the battery into the battery slot in the direction of the arrow until it clicks into place. 3 PLEASE NOTE Make sure that you allow the battery to charge for TWO hours if the computer is switched off, or for FIVE hours if the computer is switched on. It is absolutely essential that the first time you charge the battery you fully charge it. The symbol flashes when the battery charge is low. Save your data immediately and connect the power adapter. Low charge level & SUSPEND When the battery runs low (without the power adapter connected), one of these two protective functions is automatically activated: Without Save-to-Disk If there is no save-to-disk file or partition set up on your system, then current data will be stored in RAM and the system automatically switches into suspend mode. With Save-to-Disk Data is saved in the special file or partition on the hard disk reserved for this purpose. The computer then automatically switches off. If there is no saveto-disk file or partition available, the system switches into suspend mode. Never unplug a PC card while the system is in save-to-disk mode. This would deactivate the slot and problems could occur with a modified system configuration the next time you start up the computer PLEASE NOTE 51 System overview SYSTEM OVERVIEW LEFT AND RIGHT SIDES Fig. 7 (1) Modem port (2) Microphone socket (3) PC card release catch (4) PC card slot (5) Floppy disk drive eject button (6) Floppy disk drive (7) Headphones socket (8) RJ-45 network port 1 2 Fig. 8 5 4 3 (1) CD drive eject button (2) Optical digital out port (3) CD drive emergency eject button (4) CD drive (5) Battery 52 System overview REAR VIEW Fig. 9 1 2 3 4 5 6 7 8 9 * All air intake and ventilation openings must be kept free from obstructions at all times. [. . . ] You will lose all unsaved data, but the system may work properly again. Subsequently contact your dealer or customer support agent. Although I'm pressing the power switch the computer stays switched off Possible cause of the problem: The battery is missing or is incorrectly installed Note: The power on LED is not lit. Troubleshooting: o Make sure that the battery is in the battery compartment and is inserted properly. [. . . ]