User manual MAXDATA SE7505VB2

[. . . ] MAXDATA Workstation Fusion 7000 User`s Manual 2 Contents Contents 1 Setting up the system System position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connecting the system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Rear Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Powering up the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If "No" is selected and the Enter key is pressed, or the ESC key is pressed, the user is returned to where they were before F10 was pressed without affecting any existing values. F6/+ <Enter> <Esc> <F9> Table 7 describes the on-screen options you will see in BIOS Setup and what they mean. Table 7. On-Screen Options When you see this: On screen, an option is shown but you cannot select it or move to that field. On screen, the phrase Press Enter appears next to the option. What it means: You cannot change or configure the option in that menu screen. Either the option is auto-configured or auto-detected, or you must use a different Setup screen. Press <Enter> to display a submenu that is either a separate full screen menu or a popup menu with one or more choices. The following sections describe the menus and options available in BIOS Setup. MAXDATA Workstation Fusion 7000 25 Hardware Monitoring The mainboard has an integrated Winbond Heceta 836327HF chip that is responsible for hardware monitoring. Together, the Winbond Heceta chip and the Intel® LanDeskTM Client Manager (LDCM) 6 software provide basic Workstation hardware monitoring that alerts a system administrator if a hardware problem occurs. The LDCM software is for use with Windows® 2000 Workstation and Windows® 2000 Advanced Workstation operating systems. Other operating systems supported by the mainboard, such as NetWare 6. 0 or Red Hat Linux, will not be monitored with LDCM. Table 8 lists the monitored headers and sensors on the mainboard. Table 8. Monitored Headers and Sensors Sensor Type Voltage Item CPU1/2 1. 8 V VCC3 VCC +12 V 2. 5 V Vbat 5 VSB Fan Speed CPU1_FAN CPU2_FAN CHASSIS_FAN Temperature CPU1 CPU2 CHASSIS Description Monitors processor voltage (one CPU power plane) Chipset Monitors VCC3 Monitors VCC Monitors +12 V Monitors 2. 5 V (for DIMM) Battery pin voltage Monitors 5 VSB (5 V stand-by) Monitors primary processor fan speed Monitors secondary processor fan speed Monitors chassis fan speed through chassis fan header 3 only. (Total 4 chassis fans available) Monitors primary processor temperature Monitors secondary processor temperature Monitors chassis ambient temperature Serial ATA RAID BIOS Configuration NOTE To use the SATA RAID option, two SATA hard disk drives are required. Serial ATA on the mainboard is set to Base ATA mode by default. It must be changed to RAID mode before the RAID Configuration Utility can be used to configure Serial ATA RAID drives. Follow the instructions that come with this utility to change to RAID mode. 26 Configuration Software and Utilities RAID Configuration Utility The RAID Configuration Utility allows you to perform the following functions on Serial ATA drives: · · · · Create a RAID set using two SATA RAID drives Delete an existing RAID set Rebuild an existing mirrored set Resolve drive conflicts NOTE Before using the RAID Configuration Utility, set the BIOS to RAID mode. See Serial ATA RAID BIOS Configuration above. The RAID Configuration Utility can be entered only at boot-up time, while the system is in POST. To enter the utility, while the system is booting watch for the message: Press <Ctrl+S or F4> to enter RAID utility. While the message is displayed, press either the <F4> key or the <Ctrl> and <S> keys simultaneously to enter the RAID Configuration Utility. NOTE If the message does not display because the splash screen is displayed, use BIOS setup to enable the diagnostic boot screen. After entering the RAID Configuration Utility, the drives will be displayed individually, as shown in the bottom left block of the screen below. RAID Configuration Utility - Silicon Image Inc. Copyright © 2002 Creating the RAID Set 1. Use the up and down arrow keys to highlight Create RAID set. [. . . ] If it becomes necessary to update the BIOS Boot Block, this jumper should be removed during the update process. These pins should be jumpered for normal operation. NOTE: This jumper should remain in place for normal BIOS operational code updates. Default 9-10 These pins are for normal operation. BIOS Recovery 3-4 CMOS clear BIOS Booblock Write Protect 5-6 7-8 NOTE The jumper should remain on pins 7 and 8 at all times until you are instructed to perform a BIOS Boot Block update. [. . . ]