Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAXTOR ATLAS V. We hope that this MAXTOR ATLAS V user guide will be useful to you.
Lastmanuals help download the user guide MAXTOR ATLAS V.
Detailed instructions for use are in the User's Guide.
[. . . ] Atlas V
68 Pin Jumper Settings
Jumper Settings
Jumper Settings The following describes the jumper options and settings available on the Maxtor® AtlasTM V disk drive. [. . . ] The secondary option jumper block (12-pin) provides an alternate method for setting primary drive features. The alternate jumper block is located at the rear of the drive and is incorporated into the SCSI cable connector.
2 of 7
Atlas V
Jumper Settings
Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27
Signal logic_gnd logic_gnd logic_gnd logic_gnd Fault LED logic_gnd logic_gnd NC +5V out logic_gnd logic_gnd logic_gnd logic_gnd Term Power (TP)
Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28
Signal SCSI ID (A3) SCSI ID (A2) SCSI ID (A1) SCSI ID (A0) Blank (Key, no pin) Spin Delay (DS) Force SE (SE) NC Busy Out Write Protect (WP) Stagger Spin (SS) No Wide (NW) Reserved Term Power (TP)
3 of 7
Atlas V
Jumper Settings
Pin 1 3 5 7 9 11
Signal SCSI ID (A0) SCSI ID (A1) SCSI ID (A2) SCSI ID (A3) NC LED Pwr (+5V)
Pin 2 4 6 8 10 12
Signal XTFault logic_gnd logic_gnd Busy LED logic_gnd NC
4 of 7
Atlas V
Jumper Settings
SCSI ID Settings The following table identifies the various SCSI ID values and the jumper positions required to set them. Drive ID A0 (Pins 7-8) OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON A1 (Pins 5-6) OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON A2 (Pins 3-4) OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON A3 (Pins 1-2) OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON
ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9 ID 10 ID 11 ID 12 ID 13 ID 14 ID 15
5 of 7
Atlas V
80 Pin Jumper Settings
Jumper Settings
Jumper Settings The following describes the jumper options and settings available on the Atlas V SCA disk drive. Force SE (SE) (SE jumper located on J7 on PCB) Enable Single Ended operation * Indicates default jumper setting The Atlas V SCA drive does not provide support for any additional options through the use of physical jumper settings. Additional feature options are set through the SCA interface, contact your system manufacturer for details on how to set optional features. The Atlas V SCA provides support for: Stagger Spin, Spin Delay and SCSI ID selection. The Atlas V SCA does not provide support for: SE jumper on
Enable auto switch between Single Ended or LVD operation SE jumper off*
6 of 7
Atlas V
Jumper Settings
Active Termination enable, Termination Power and Write Protect. Jumper Locations The Atlas V SCA disk drive has only one location (J7 on PCB) where user configurable jumpers are found. [. . . ] Contact your system manufacturer for details on setting SCSI ID.
7 of 7 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MAXTOR ATLAS V
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAXTOR ATLAS V will begin.
