User manual MAXTOR BARRACUDA 1 INSTALLATION REV D

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAXTOR BARRACUDA 1. We hope that this MAXTOR BARRACUDA 1 user guide will be useful to you.

Lastmanuals help download the user guide MAXTOR BARRACUDA 1.

Download

Manual abstract: user guide MAXTOR BARRACUDA 1INSTALLATION REV D

Detailed instructions for use are in the User's Guide.

 [. . . ] Installation Guide
            
ST12550N/ND/W/WD
            
ST11950N/ND/W/WD
                      
Disc Drive
       
BARRACUDA 1 and 2
       
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrostatic discharge protection . . . . . . . . . . . . . . . . . . . . . . . . . . . Important safety information and precautions . . . . . . . . . Wichtige Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  [. . . ] Other controllers do not allow this so be sure to refer to your system or controller user's manual for details about its requirements for proper SCSI device installation. Use connector J4 to set the SCSI ID on ST11950N/ND and ST12550N/ND drives (Figure 3). Use connector J5 to set the SCSI ID on ST11950W/WD and ST12550W/WD drives (Figure 4). Most Barracuda 1 and 2 disc drives are factory set with the SCSI ID set at 0. To change the SCSI ID,  install jumpers on the appropriate pins as shown in the illustrations. If,  after completing the installation process,  the drive's LED does not show on/off activity when the host is trying to communicate with the drive,  a duplicate SCSI ID may be the problem. If this is the case,  change the ID so that each device on the SCSI chain has its own unique ID. 

ST11950 and ST12550 Installation Guide,  Rev. D 21 Also check your system or controller user's manual to ensure that you have not violated its SCSI ID numbering recommendations. 
SCSI Connector DC Power Connector

J01 Pin 1 J4
ID1 ID0

ID2

Select SCSI ID by placing jumpers as shown below. SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7

J4

Figure 3. Setting the SCSI ID on N- and ND-type drives

22

ST11950 and ST12550 Installation Guide,  Rev. D
SCSI I/O Connector J5 Pin 1 Pin 1 DC Power Connector

4P

3P 2P

1P

ID3 ID1 ID2 ID0

J5
SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 SCSI ID = 8 SCSI ID = 9 SCSI ID = 10 SCSI ID = 11 SCSI ID = 12 SCSI ID = 13 SCSI ID = 14 SCSI ID = 15

Figure 4. Setting the SCSI ID on W- and WD-type drives

ST11950 and ST12550 Installation Guide,  Rev. D 23 Terminating the drive If you are installing the drive in a system that has other SCSI devices installed,  terminate only the end devices on the SCSI chain. A SCSI "device" is any disc drive,  scanner,  tape backup unit,  or other piece of hardware connected to your system using the SCSI bus. The top example in Figure 5 shows an internal hard disc at one end of the SCSI bus with the SCSI controller at the other end (both are terminated). The bottom example shows two additional SCSI devices connected externally--this means the SCSI controller is no longer on the end of the SCSI chain and should not be terminated. 
Internal SCSI cable Internal SCSI device Internal SCSI device Terminate Internal SCSI cable Internal SCSI device Internal SCSI device Controller External SCSI cable Controller

External SCSI device

External SCSI device

Terminate

Figure 5. SCSI bus termination

24 ST11950 and ST12550 Installation Guide,  Rev. D Refer to the appropriate section below for instructions in terminating a drive. Installing or removing terminator packs improperly can result in damage to the terminators or surrounding components. ST11950N and ST12550N drives To terminate ST11950N and ST12550N drives,  install terminator packs as shown in Figure 6. 
I/O Terminator Packs (single-ended I/O only)

Pin 1 End (of terminator)

Figure 6. Installing terminator packs (ST11950N shown)

ST11950 and ST12550 Installation Guide,  Rev. All single-ended terminators must be ANSI SCSI-2 alternative 2 active terminators.  [. . . ] D darf nicht gedehnt oder gedrückt werden und es darf den Luftstrom zur Kühlung des Systems nicht behindern. Das Laufwerk wird über einen 4-poligen,  neben dem SCSI-Anschluß befestigten Steckverbinder mit Gleichstrom versorgt. Der Ausgang eines Netzteils muß SELV (safety extra low voltage) nach IEC 950 entsprechen. Abbildung 16 zeigt die Steckerbelegung für den Gleichstromanschluß.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAXTOR BARRACUDA 1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAXTOR BARRACUDA 1 will begin.