User manual MAXTOR BARRUCA 7200.7 PLUS

[. . . ] Barracuda 7200. 7 Plus ST3200822A ST3200021A Barracuda 7200. 7 ST3160023A ST3160021A ST3120026A ST3120022A ST380013A ST380011A ST340014A Barracuda 7200. 7 Plus ST3200822A ST3200021A Barracuda 7200. 7 ST3160023A ST3160021A ST3120026A ST3120022A ST380013A ST380011A ST340014A ©2003, 2004, 2005 Seagate Technology LLC All rights reserved Publication number: 100217279, Rev. N September 2005 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives. Barracuda 7200. 7 Product Manual, Rev. N 17 18 Barracuda 7200. 7 Product Manual, Rev. N 3. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3. 1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: · The SeaShellTM replaces electrostatic discharge (ESD) bags. The SeaShell package is a shock-ribbed, transparent clamshell enclosure that limits a drive's exposure to ESD and also protects against external shocks and stresses. The design permits attaching cables, software loading and label/barcode scanning without removing the drive from the SeaShell. Keep the drive in the SeaShell package until you are ready for installation. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Handle the drive by its edges or frame only. · The drive is extremely fragile--handle it with care. Do not press down on the drive top cover. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. Barracuda 7200. 7 Product Manual, Rev. N 19 3. 2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather Hole Do not cover or seal. Figure 3. Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole. This hole has two purposes: · To allow condensation inside the hard disc to escape · To allow air pressure inside the hard disc to equalize with ambient pressure Note. If this hole is covered, sealed, or penetrated by any object, the drive reliability may be compromised and could lead to permanent damage--doing so voids the warranty. 20 Barracuda 7200. 7 Product Manual, Rev. N 3. 3 3. 3. 1 Jumper settings Master/slave configuration The options jumper block shown in Figure 1 is used to configure the drive for operation. [. . . ] (Central Europe time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands. Seagate Service Centers Toll-free support numbers Call center Austria Belgium Denmark France Germany Ireland Italy Netherlands Norway Poland Spain Sweden Switzerland Turkey United Kingdom Presales and Technical Support -- 00 800-47324283 (00 800-4SEAGATE) 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-311 12 38 00 800-47324283 00 800-47324283 00 800-47324283 00 800-31 92 91 40 00 800-47324283 Warranty Service 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-311 12 38 00 800-47324289 00 800-47324289 00 800-47324289 00 800-31 92 91 40 00 800-47324289 FAX services--All Europe (toll call) Technical Support Warranty Service +1-405-324-3339 +31-20-653-3513 Africa/Middle East support services For presales and technical support in Africa and the Middle East, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A. M. (Central Europe time) Monday through Friday. The presales and technical support call center is located in Oklahoma City, USA. [. . . ]