User manual MAXTOR MARATHON 840SL

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marathon 1430sl, Marathon 1350sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marathon 1080sl, Marathon 840sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATA Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marathon 1430sl, Marathon 1350sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marathon 1080sl, Marathon 840sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Drives are tested in representative end-user systems using 80486, Pentium and PowerPC microprocessors. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all 16 Marathon 1430sl, 1350sl, 1080sl and 840sl Product Manual systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. The computer manufacturer or system integrator should confirm EMC compliance and provide CE marking for their products. 1. 11. 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure, not attached as an external device. As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required. has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc. ) complies with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, try one or more of the following corrective measures: · Reorient the receiving antenna. · Move the device to one side or the other of the radio or TV. · Move the device farther away from the radio or TV. · Plug the computer into a different outlet so that the receiver and computer are on different branch outlets. If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find the following booklet from the Federal Communications Commission helpful: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4. Marathon 1430sl, 1350sl, 1080sl and 840sl Product Manual 17 2. 0 Drive mounting and configuration 2. 1 Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and ESD hazards. You must observe standard staticdischarge precautions. Handle the drive only by the sides of the head/disc assembly. [. . . ] commands and implementation, see the Working Draft of the Proposed American National Standard X3T10/2008D Revision 6, Information Technology AT Attachment-3 Interface (ATA-3). You must have a recent BIOS or software package that supports S. M. A. R. T. command by writing B0H to the Command Register, the host must do the following: · Write the value 4FH to the Cylinder_Low register · Write the value C2H to the Cylinder_High register · Write the appropriate S. M. A. R. T. code to the Features register, as shown in the table below: Code in Features Register D8H D9H DAH Supported by 1430sl, 1350sl, 1080sl and 840sl Yes Yes Yes S. M. A. R. T. [. . . ]