User manual MAXTOR MEDALIST 1270SL

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist SL Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 1080sl, Medalist 1270sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ATA Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist SL Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures: · Reorient the receiving antenna. · Move the device to one side or the other of the radio or TV. · Move the device farther away from the radio or TV. 16 Medalist SL Family Product Manual, June 1996 · Plug the equipment into a different outlet so that the receiver and computer are on different branch outlets. If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4. This digital apparatus does not exceed the Class B limits for radio noise emissions from computer equipment as set out in the radio interference regulations of the Canadian Department of communications. Le présent appareil numérique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umgebungstemperatur von 55°C vorgesehen ist. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht mehr als 5, 08 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V ± 5% 0, 6A +12V ± 5% 0, 8A (1, 9A fur ca. Die Versorgungsspannung muss SELV entsprechen. Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebildetem Servicepersonal durchgeführt werden. Bitte schaffen Sie Festplatteetiketten nicht weg. Der Einbaudes Drives muss den Anforderungen gemäss DIN IEC 950V DC 0805/05. 90 entsprechen. Medalist SL Family Product Manual, June 1996 17 2. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 2. 1 Handling and static-discharge precautions After you unpack the drive, and before you install it in a system, be careful not to damage it through mishandling or static discharge. Wool and synthetic clothing, carpet, plastic and styrofoam are contributors to static-charge buildup. This charge is released when you touch another conductor and may damage sensitive components in the drive. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in its static-shielded bag until you are ready to complete the installation. Do not attach any cables to the drive while it is in its static-shielded bag. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. [. . . ] The drive is shipped with the timer disabled. 3. 2. 4 Active and Set Idle Timer command (FBH) This is a Seagate-unique power command. It moves the drive immediately to Active mode. When the drive receives this command, it asserts Busy in the Host Status register, initiates entry into Active mode, negates Busy and generates an interrupt. If the drive is in Standby mode, it does not wait for the spinup to complete before issuing the interrupt. [. . . ]