User manual MAXTOR MEDIALIST 2110 INSTALLATION

[. . . ] INSTALLATION INSTRUCTIONS WHAT YOU NEED HANDLE WITH CARE! Disc drives are extremely fragile. Do not drop or jar your drive. MEDALIST HARD DRIVE INSTALLATION GUIDE Medalist 2110 (ST32110A) ATA (IDE) Hard Drive Installing your new Seagate® Medalist® hard drive is as easy as 1, 2, 3. Follow the instructions in this installation sheet to install and configure your new drive. For additional information and troubleshooting tips, see the back of this sheet. [. . . ] · Check for viruses. INSTALLATION INSTRUCTIONS MEDALIST HARD DRIVE INSTALLATION GUIDE Medalist 2110 (ST32110A) ATA (IDE) Hard Drive Installing your new Seagate® Medalist® hard drive is as easy as 1, 2, 3. Follow the instructions in this installation sheet to install and configure your new drive. For additional information and troubleshooting tips, see the back of this sheet. If you have additional questions, call your computer dealer, or contact Seagate indicates that additional infortechnical support. This symbol: mation on a topic appears on the back of this sheet. BEFORE YOU BEGIN Caution. Do not format this drive without first transferring the free Disk Manager software that is stored on the drive. See the instructions below for details. · · DRAFT Make sure your computer is turned off before you open the case. Read the handling precautions to the right, and inspect the drive to make sure that it is not damaged. Save your foam-lined Seagate disc drive shipping container. This box has been approved by Seagate for shipping a Seagate disc drive. Using any other container or packing material voids your drive warranty. · 1 1. ONE DRIVE OR TWO? If you do not already have a hard drive in your computer and you are installing only one new drive, you do not have to change any jumper settings. In this case, skip ahead to "Attaching Cables and Mounting the Drive. " If you already have one hard drive in your computer and you are installing a second drive, you must configure one drive as a master and the other as a slave. The master drive will be the "boot" drive (drive C), from which the computer loads system software when it first starts up. To configure your new Seagate drive as the master, place a jumper on pins 5 and 6 (see below). To configure the drive as a slave, remove all jumpers. If you need to change the jumpers on your existing hard drive, see the Disk Manager online manual, look on the drive label, or contact the drive manufacturer for master/slave jumper settings. 40-pin ATA interface connector ATTACHING CABLES AND MOUNTING THE DRIVE 1 If you are installing a new ATA interface cable, attach one end of the cable to the interface connector on your computer or host adapter. The ATA cable must be no more than 18 inches long. 2 Thread the interface cable through the drive bay and attach the connector at the end of the interface cable to your new drive. If you have two drives, attach the second drive to the second connector. Pin 1 pin 1 4-pin power connector ! 2 468 1357 Master/slave jumper settings Drive is slave Drive is master in singleor dual-drive system Caution. Make sure to align pin 1 on the computer or host adapter with pin 1 on your drive or drives. Pin 1 on the interface cable is usually indicated by a stripe along the edge of the cable. WHAT YOU NEED HANDLE WITH CARE! Disc drives are extremely fragile. [. . . ] Zur Befestigung des Laufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht mehr als 3, 3 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V ± 5% 0, 6A; +12V ±% 0, 8A (1, 9A fur ca. Die Versorgungsspannung muss SELV entsprechen. [. . . ]