User manual MAXTOR MOMENTUS 5400 FDE REV C

[. . . ] Product Manual Momentus 5400 FDE ® ST9120826A ST9100826A ST980821A ST960814A ST940811A 100377037 Rev. C August 2007 ©2004-2007, Seagate Technology LLC All rights reserved. C August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, SeagateSeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. [. . . ] · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. The sole exception to this statement is for the Momentus®5400 FDE perforated label which you should remove and attach to the exterior of the computer system. Momentus 5400 FDE Product Manual, Rev. C 19 3. 2 3. 2. 1 Jumper settings Master/slave configuration Use the options jumper block shown in Figure 6 to configure the drive for operation. This jumper block is the 4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see Section 3. 2. 2. The "Master or single drive" option is the factory default setting. Drive is master (or single drive) Drive is slave Cable select Figure 6. Jumper settings 3. 2. 2 Cable-select option Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper as shown in Figure 6. Refer to your computer manual to determine whether your computer supports this option. 3. 3 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 7 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow these important mounting precautions when mounting the drive: · Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. · Use only M3 x 0. 5 mounting screws. · Do not overtighten the mounting screws (maximum torque: 4. 0 inch-lb). · Four (4) threads (0. 080 inches) minimum screw engagement recommended. 20 Momentus 5400 FDE Product Manual, Rev. C . 157 (3. 9878) . 399 (10. 135) 3. 945 +/-0. 010 (100. 2 +/-. 25) 0. 490 +/- . 010 (12. 446 +/- . 254) 0. 673 +/- . 010 (17. 09 +/- . 254) 2. 750 +/- . 010 (69. 85 +/- . 25) Breather Hole Do not cover or seal. Recommended case temp. measurement location . 551 (13. 99) 3. 567 (90. 60) . 374 +/- . 008 (9. 5 +/- . 2) 2X . 118 (3. 00) Both sides . 551 (13. 99) 3. 567 (90. 60) 2X M3 X 0. 5-6H Mounting holes Both sides . 12 min. full thread 4X M3 X 0. 5-6H Mounting holes . 10 min. full thread inches (mm) 2. 430 (61. 72) . 399 (10. 135) Detail A Detail A . 160 (4. 06) Figure 7. Mounting dimensions--top, side and end view Momentus 5400 FDE Product Manual, Rev. [. . . ] Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate. com Technical Support: DiscSupport@Seagate. com Warranty Support: http://www. seagate. com/support/service/index. html mySeagate my. seagate. com is the industry's first Web portal designed specifically for OEMs and distributors. It provides self-service access to critical applications, personalized content and the tools that allow our partners to manage their Seagate account functions. Submit pricing requests, orders and returns through a single, password-protected Web interface-anytime, anywhere in the world. [. . . ]