User manual MAXTOR ST31000526SV PRODUCT MANUAL REV D

[. . . ] Product Manual SV35 SeriesTM ST2000VX002 ST31000526SV ST31000525SV ST3500411SV ST3500410SV ST3250311SV 100562053 Rev. D January 2011 Revision history Revision Date Sheets affected or comments Rev. D 03/06/09 07/08/09 06/03/10 01/05/11 Initial release. Added new 2TB model and updated specifications. Copyright © 2011 Seagate Technology LLC. [. . . ] 2TB model 5Hz­22Hz 22Hz­350Hz 350Hz­500Hz 0. 25 Gs (Limited displacement) 5. 0 Gs 2. 0 Gs 1TB and 500GB models 5Hz­22Hz 22Hz­350Hz 350Hz­500Hz 0. 25 Gs (Limited displacement) 5. 0 Gs 2. 0 Gs 250GB models 5Hz­350Hz 350Hz­500Hz 5. 0 Gs 1. 0 Gs 2. 10 Acoustics emissions Drive emission of sound is measured consistent with the ECMA-74 and its referenced standards. Testing is conducted at room temperature (approximately 25 degrees C). Emission levels are reported as the total A-weighted sound power levels for, steady state, idle and active (seek) modes of operations. Table 6: Drive A-weighted Sound Power Levels (SWL, BA) Idle[1] 2000 GB 1000GB and 500GB models 250 GB model [1] 2. 1 bels (typ) 2. 3 bels (max) 2. 7 bels (typ) 2. 9 bels (max) 2. 5 bels (typ) 2. 8 bels (max) Seek 2. 3 bels (typ) 2. 4 bels (max) 2. 8 bels (typ) 3. 0 bels (max) 2. 6 bels (typ) 2. 8 bels (max) During periods of drive idle, some offline activity may occur according to the S. M. A. R. T. specification, which may increase acoustic and power to operational levels. Test for Prominent Discrete Tones (PDTs) Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. * Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies. SV35 Series SATA Product Manual, Rev. D 15 2. 11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Table 7: Test Electrostatic discharge Radiated RF immunity Electrical fast transient Surge immunity Conducted RF immunity Voltage dips, interrupts Radio frequency environments Description Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV 80 to 1000MHz, 3 V/m, 80% AM with 1kHz sine 900MHz, 3 V/m, 50% pulse modulation @ 200Hz ± 1kV on AC mains, ± 0. 5 kV on external I/O ± 1kV differential, ± 2 kV common, AC mains 150kHz to 80MHz, 3 Vrms, 80% AM with 1kHz sine 0% open, 5 seconds 0% short, 5 seconds 40%, 0. 10 seconds 70%, 0. 01 seconds Performance level B A Reference standard EN 61000-4-2: 95 EN 61000-4-3: 96 ENV 50204: 95 EN 61000-4-4: 95 EN 61000-4-5: 95 EN 61000-4-6: 97 EN 61000-4-11: 94 B B A C C C B 2. 12 Warranty To determine the warranty for a specific drive, use a web browser to access the following web page: support. seagate. com/customer/warranty_validation. jsp From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number(or part number) and country of purchase. The system will display the warranty information for your drive. 2. 13 2. 13. 1 Agency certification Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency. 2. 13. 2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products. Korean RRL 16 SV35 Series SATA Product Manual, Rev. D If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission, Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab. · Family name: SV35. 5 Series · Certificate number: STX-720012 (B) Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). [. . . ] Sector Count register values: 00H Set PIO mode to default (PIO mode 2). 01H Set PIO mode to default and disable IORDY (PIO mode 2). 08H PIO mode 0 09H PIO mode 1 0AH PIO mode 2 0BH PIO mode 3 0CH PIO mode 4 (default) 20H Multiword DMA mode 0 21H Multiword DMA mode 1 22H Multiword DMA mode 2 40H Ultra DMA mode 0 41H Ultra DMA mode 1 42H Ultra DMA mode 2 43H Ultra DMA mode 3 44H Ultra DMA mode 4 45H Ultra DMA mode 5 46H Ultra DMA mode 6 10H 55H 82H 90H AAH F1H Enable use of SATA features Disable read look-ahead (read cache) feature. Disable write cache Disable use of SATA features Enable read look-ahead (read cache) feature (default). [. . . ]