User manual MAXTOR ST32271N INSTALLATION

[. . . ] · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· Barracuda 4LP · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· Disc Drive · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· ST34371N/W/WC/WD/DC · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· ST32171N/W/WC/WD/DC · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· ST34571N/W/WC/WD/DC · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· ST32271N/W/WC/WD/DC · ·· · · ·· · · ·· · · ·· · ·· · · ·· · · ·· Installation Guide Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Electrostatic discharge protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Important safety information and precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Wichtige Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A SCSI "device" is any disc drive, scanner, tape backup unit, or other piece of hardware connected to your system using the SCSI bus. The top example in Figure 2 shows an internal hard disc at one end of the SCSI bus with the SCSI controller at the other end (both are terminated). The bottom example shows two additional SCSI devices connected externally--this means the SCSI controller is no longer on the end of the SCSI chain and should not be terminated. Some controllers prefer to remain terminated even if they are in the middle of the chain. Also, some controllers treat the internal and external chains as separate logical buses. This means you may need to terminate both the first and last devices on both logical buses to achieve proper termination. If necessary, refer to your system or controller documentation to see how this is handled in your particular system. 20 Barracuda 4LP Installation Guide, Rev. B For information about how to terminate your drive, refer to the appropriate drive-specific section. Internal SCSI cable Internal SCSI device Internal SCSI device Terminate Internal SCSI cable Internal SCSI device Internal SCSI device Controller External SCSI cable Controller External SCSI device External SCSI device Terminate Figure 2. SCSI bus termination Terminator power You usually will not need to change this option and can normally leave the drive configured as it was shipped from the factory. For information about how to change the terminator power option on your drive, refer to the appropriate drive-specific section. I/O circuits and data path widths · "WD" and "DC" models use differential I/O circuits. You cannot mix these models with single-ended models ("N, " "W, " "WC") on the same SCSI bus. The circuits are incompatible with each other. · "W, " "WD, " and "WC" models have a "wide" (16-bit) SCSI data bus rather than the standard (non-wide) 8-bit SCSI data bus; however, you can use these wide drives on a standard (nonwide) 8-bit data bus. Barracuda 4LP Installation Guide, Rev. B 21 Figures 3a, 3b, 3c, and 3d show typical drive connections. The following table lists the maximum cable lengths and number of devices with single-ended I/O circuits allowed on a daisy-chain cable for <10 and <20 M transfers/sec I/O data transfer rates. Cable characteristics for single-ended circuits Maximum number of devices on line Maximum cable length allowed I/O transfer rate <10 M transfers/s 8 (reg. SCSI bus) <10 M transfers/s 16 (wide SCSI bus) 6 meters (19. 7 ft. ) 6 meters (19. 7 ft. ) <20 M transfers/s 4 (reg. /wide SCSI bus) 3 meters (9. 8 ft. ) <20 M transfers/s 8 (reg. /wide SCSI bus) 1. 5 meters (4. 9 ft. ) For devices having differential I/O circuits, a maximum cable length of 25 meters (82 feet) is allowed. A maximum of 8 devices can be connected on an 8-bit wide data bus, and a maximum of 16 devices can be connected on a 16-bit wide data bus. 22 Barracuda 4LP Installation Guide, Rev. B HDA Pin 1 Figure 3a. Fifty pin I/O connection to drive HDA Pin 1 Figure 3b. Sixty-eight pin connection to drive Barracuda 4LP Installation Guide, Rev. B "N" Model Drive 23 SCSI ID X (or last drive) [1] Additional SCSI devices SCSI ID 1 Pin 1 (check your adapter for Pin 1 location) SCSI ID 7 Host Adapter PCB SCSI ID 0 [1] "X" means up to 6 or the maximum allowable number of devices on the SCSI bus. See Table 4 and system documentation. Figure 3c. Multiple drive connection to host adapter 24 "W" Model Drive [1] Barracuda 4LP Installation Guide, Rev. [. . . ] Power to SCSI Bus Host adapter or other device provides term. power to external terminator. (default) Position A (default) J2 J6 Drive Front J2 Jumper Type (enlarged to show detail) DC Power Connector SCSI I/O J1 Connector Figure 14. Setting terminator power jumpers 44 Barracuda 4LP Installation Guide, Rev. B W/WD drives Other applicable jumper options Other option jumpers are available as illustrated below. Drive with HDA up, PCB down, viewed from front J2 HDA Pin 1 Reserved Delay Motor Start option (valid only if the Enable Motor Start jumper is not connected) Disable the Delay Motor Start option. [. . . ]