User manual MAXTOR ST340015ACE

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Barracuda 5400. 1 Family ST340015ACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA Interface Drives Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Barracuda 5400. 1 Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST340015ACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 2003­2004 Seagate Technology LLC All rights reserved Publication number: 100256414, Rev. G May 2004 Seagate, Seagate Technology, and the Seagate logo are either registered trademarks or trademarks of Seagate Technology LLC. Barracuda, DiscWizard, SeaFONE, SeaShell, SeaShield, SeaTDD, and 3D Defense System are either registered trademarks or trademarks of Seagate Technology LLC. [. . . ] G 21 3. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3. 1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: · The SeaShellTM replaces electrostatic discharge (ESD) bags. The SeaShell package is a shock-ribbed, transparent clamshell enclosure that limits a drive's exposure to ESD and also protects against external shocks and stresses. The design permits attaching cables, software loading and label/ barcode scanning without removing the drive from the SeaShell. Keep the drive in the SeaShell package until you are ready for installation. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Handle the drive by its edges or frame only. · The drive is extremely fragile--handle it with care. Do not press down on the drive top cover. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. 22 3. 2 Barracuda 5400. 1 Product Manual, Rev. G Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather Hole Do not cover or seal. Figure 3. Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole. This hole has two purposes: · To allow condensation inside the hard disc to escape · To allow air pressure inside the hard disc to equalize with ambient pressure Note. If this hole is covered, sealed, or penetrated by any object, the drive reliability may be compromised and could lead to permanent damage--doing so voids the warranty. Barracuda 5400. 1 Product Manual, Rev. G 3. 3 3. 3. 1 Jumper settings Master/slave configuration 23 The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. [. . . ] You can send questions or comments 24 hours daily and exchange messages with a technical support specialist from 8:00 A. M. (Central time) Monday through Friday. Warranty Service Seagate offers worldwide customer support for Seagate drives. Seagate distributors, OEMs and other direct customers should contact their Seagate service center representative for warranty-related issues. Resellers or end users of drive products should contact their place of purchase or one of the Seagate warranty service centers for assistance. [. . . ]