User manual MAXTOR ST5660N

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decathlon Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST5660N, ST5660NC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCSI Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Decathlon Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST5660N, ST5660NC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the PMI bit is one, the drive returns the read capacity data, which contains the logical block address and block length of the last logical block address, after which a substantial delay (approximately 1 msec) in data transfer occurs. This logical block address must be greater than or equal to the logical block address specified in the CDB. This reported logical block address is a cylinder boundary. Byte 8 Decathlon Family Product Manual, Rev. B 57 3. 5. 1. 1 Read Capacity data The Read Capacity data is shown below. Bytes 0­3 4­7 Bytes 0­3 Bits 7 6 5 4 3 2 1 0 Logical block address Block length (00000200H) The logical block address is determined by the PMI bit in the CDB of the Read Capacity command. The PMI bit is described in Section 3. 5. 1. The block length is always 512. Bytes 4­7 3. 5. 2 Read Extended command (28H) When the drive receives the Read Extended command, it transfers data to the initiator. This command is the same as the Read command discussed in Section 3. 4. 6, except that in the CDB for the Read Extended command, a 4-byte logical block address and a 2-byte transfer length can be specified. If there is a reservation access conflict, this command terminates with a reservation conflict status and no data is read. For more information about the reservation conflict status, see Section 3. 2. Bytes 0 1 2­5 6 7­8 9 Byte 1 0 0 0 0 0 Bits 7 0 6 0 LUN 0 5 1 4 0 DPO 0 0 3 1 FUA 0 0 2 0 0 0 0 1 0 0 0 Flag 0 0 Rel Adr 0 Link Logical block address Transfer length If the disable page out (DPO) bit is one, the cached data that the drive receives during this command has the lowest priority for being retained in the cache. If the DPO is zero, the cached data has the highest priority for being retained in the cache. 58 Decathlon Family Product Manual, Rev. B If the forced unit access (FUA) bit is one, the drive must access the disc to get the data requested by the initiator, even if the data is available in the cache. If the FUA bit is zero, the drive can get the data from the cache or the disc. If the RelAdr bit is zero, the logical block address field specifies the first logical block of the range of logical blocks to be written and verified by the drive. If the RelAdr bit is one, the logical block address field is a two's complement displacement. This displacement is added to the logical block address last accessed on the drive to determine the logical block address for this command. Set the RelAdr bit to one only if linked commands are used. Bytes 2­5 Bytes 7­8 The logical block address specifies the logical block where the read operation begins. The transfer length specifies the number of contiguous logical blocks of data to be transferred. A transfer length of 0 means that no logical blocks are to be transferred. This condition is not considered an error. [. . . ] Last command byte to data in Description Command to data in or parameter in Symbol T06 Typical Max Command-dependent 122 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Decathlon Family Product Manual, Rev. B DB(0­7, P)­ Last byte First byte ATN­ SEL­ BUSY­ I/O­ MSG­ C/D­ REQ­ ACK­ T07, T08 Figure 18. Last command byte to data out Description Command to data out or parameter out Command to data (write to data buffer) Symbol T07 T08 Typical Max Command-dependent <500 µsec 1, 025 µsec Decathlon Family Product Manual, Rev. B 0 1 0 1 0 1 0 1 0 1 0 123 DB(0­7, P)­ Identify message First byte ATN­ SEL­ BUSY­ I/O­ MSG­ 1 0 1 0 1 0 1 C/D­ REQ­ ACK­ T16 Figure 19. [. . . ]