Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAXTOR ULTRA ATA133. We hope that this MAXTOR ULTRA ATA133 user guide will be useful to you.
Lastmanuals help download the user guide MAXTOR ULTRA ATA133.
Detailed instructions for use are in the User's Guide.
[. . . ] Ultra ATA/133 Hard Drive Mounting Kit
Installation Guide Ultra ATA/133 Hard Drive Mounting Kit
Kit Components
· UDMA 133 IDE interface cable · Two 5. 25-inch mounting brackets · Eight mounting screws
Tools Required for Installation
· A small (#2) Phillips screw driver · Your computer user manual
Handling Precautions
DO ground yourself before handling the drive to avoid the risk of exposing it to electrostatic discharge. Use a grounding strap or touch a metal part of your computer's case when your system is powered down AND connected to an electrical outlet. DON'T connect/disconnect any cables to the drive or system when the power is ON. [. . . ] The short side of the bracket should face inward against the drive. Repeat steps 2 and 3 to attach the second mounting bracket to the other side of the drive. Insert the bracketed drive into the selected 5. 25-inch device bay in your system and use the four remaining screws to attach the drive to the sides of the bay. Be careful not to touch the green circuit board on the bottom of the drive. Note: Make sure the ATA connector end of the drive is facing the interior of your computer case so you can connect the interface and power cables.
Mounting Screws
3. Using two of the included screws, attach the bracket to the drive. Warning: Using any screws except those supplied may cause damage to your drive or system.
UDMA Interface Cable Mounting Bracket
Computer with available 5. 25-inch device bay
Ultra ATA/133 Hard Drive Mounting Kit
Attaching the UDMA 133 Cable
Determine if the hard drive you are adding will be used in master or slave configuration. Configure the drive's jumper settings to match. Refer to your hard drive installation instructions for proper jumper settings. Tip: A jumper is a small plastic piece that slides over a pair of configuration pins. These configuration pins are usually located adjacent to the ATA connector on the rear of the drive. Connect the cable to the ATA connectors on the hard drive and motherboard/ATA adapter card as shown in the figure below. Be sure to orient each cable connector correctly before inserting it into an ATA connector. The correct orientation of the cable connector can be found by matching the groove on one side of the cable connector with the corresponding notch in the ATA connector.
Striped/Colored Edge (pin 1)
Drive 1 - Slave (gray) Motherboard/ATA Adapter Card Connector (blue) Drive 0 - Master (black)
UDMA Interface Cable (industry standard cable length - 18 inches)
Warranty: MAXTOR MAKES NO REPRESENTATION OR WARRANTY CONCERNING THE QUALITY, PERFORMANCE OR OTHER CHARACTERISTICS OF THE ULTRA ATA/133 INTERFACE CABLE, 2 MOUNTING BRACKETS, AND 8 SCREWS ("HARD DRIVE MOUNTING KIT"). [. . . ] Maxtor® is a registered trademark of Maxtor Corporation. Other brands or products are trademarks or registered trademarks of their respective holders. Maxtor P/N: 20148001, rev A
www. maxtor. com [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MAXTOR ULTRA ATA133
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAXTOR ULTRA ATA133 will begin.
