User manual MAYTAG SATELLITE

[. . . ] Cylinder Cleaner How do you clean your space? Add wings to your cleaning with the new Maytag cylinder cleaner. The cleaner you have purchased is more than just a vacuum. You have purchased a new way to clean your space, simplify your life, and complement your home décor. The Maytag cylinder cleaner's powerful motor, ingenious design and impeccable style complement all of your cleaning needs. www. maytag. co. uk Contents Important safeguards . [. . . ] Telescoping Extension Wand - Used with the flexible clear hose and any tool you can clean your ceiling, floors, or stairs in one easy step. Adjust the wand to the desired length, release latch and you are ready to go. Because the extension wand is light and easy to use, you'll tire less--making all of your above-floor cleaning a breeze. Tool Holder - Tools are easily accessible and ready to use for all your cleaning needs. Extra Filter Bag - (one installed in cleaner) The Maytag cylinder cleaner doesn't stop at effortless cleaning; it also uses a HEPA filtration waste-bag so that the air coming out of your cylinder cleaner is cleaner than the air it's sucking in. The HEPA filtration bag traps dirt, dust mites and other small particles leaving you with a cleaner space. B C D E F G I H J (Cont'd) ¡ 3 Attach hose, wand, tools and nozzle A 1-2 Attach hose Insert hose connector (A) into opening (B) in bag lid, aligning tabs on hose connector with slots in opening. To remove hose, twist hose connector clockwise and pull up. B C 1-3 Attach wand To attach wand to hose, push wand firmly onto hose; twist wand to tighten. To adjust the telescoping wand, push spring latch (C) and pull down on lower portion of wand. Release latch to lock the wand in position. 1-4 Attach tools and nozzle To attach tool to the hose or wand, firmly push tool onto hose or wand. Twist tool slightly to tighten or loosen connection. To attach either nozzle to the wand, push the nozzle firmly onto the wand. Twist nozzle slightly to tighten or loosen connection. 9 2. How to use Cleaner description 2-1 Use the following to identify the parts and 10 8 7 11 12 13 14 2 6 4 5 3 1. 4. 15 1 4 features of the cleaner: Turbine nozzle Bag lid Bag lid latch (on rear of cleaner) Wand storage/tool storage slot (at rear of carrying handle) 5. Wand/tool storage holder: fits into storage slot on rear of carry handle 9. Telescoping extension wand: used with turbine nozzle, floor brush or tools. Operate cleaner only at voltage specified on data plate on underside of the cleaner. This cleaner is intended for household use. 2-2 ON/OFF switch To turn cleaner ON, push the ON/OFF switch (A) down. To turn cleaner OFF, push the switch up. A Wand/tool storage holder (C) at the rear of the carry handle. Tools may be positioned on the tool holder attached to the wand for convenient storage. 2-3 The wand/tool storage holder (B) fits into the slot C B Cleaning tools Cleaning tool storage (D). Fit the tool holder into the slot (C) at the rear of the carry handle. Select the tool best suited for the cleaning task from the following descriptions. C 2-4 The tools may also be stored on the tool holder D Select the proper tool ners, and along edges in such places as dresser drawers, upholstered furniture, and stairs. [. . . ] Discard used bag. B 3-3 Slide new bag collar all the way down into bag holder. 6 Close bag lid, making sure bag is completely inside bag compartment. Close and latch bag lid. 3-4 Secondary filter Disconnect cleaner from electrical outlet. The secondary filter, located in the bag compartment, protects the motor from dirt particles. To replace the filter when it becomes dirty, remove the disposable bag, following Figs. [. . . ]