User manual MB QUART ALEXXA INSTALLATION

[. . . ] - Use a clean dry cloth to clean the speakers when necessary. - Refer all service to a qualified authorized service center. Minimum Tool Required Material Supplied - Wire Strippers - Grille Removal Tool - Carpenters Level - Speaker Cut-Out Template - # 2 Phillips Screwdriver - Paint Shield - Flat Blade Screwdriver - Owner / Install manual - Electronic Stud Finder - Drywall Hand Saw - Miniature Flat Blade Screwdriver for Point Source Speakers SPEAKER PLACEMENT (ALX2PS / ALX3PS / ALX5. 25IC / ALX6. 5IC / ALX6. 5IC DM / ALX8. 0IC) These speakers are designed to operate in a standard drywall or suspended acoustical panel ceiling. The speaker enclosure allows for different mounting depths that may be encountered in different ceiling applications. [. . . ] Use the speaker cut-out template supplied to mark your hole locations. (Be sure there is clearance behind the area you have chosen for the speaker. Avoid electrical wiring, plumbing, moving parts, air ducts and Fire Stops. Use a drywall saw or other appropriate tool to carefully cut out the speaker holes. The cut-out is the exact size required for the speaker. You also can go as much as 1/4" over this size as "Mistake Room". Connect the speaker wires (18 gauge wire not supplied) to the speakers as shown in DIAGRAM 5. (Be sure to get the + and - polarity correct) 5. Place the speaker into the speaker opening and using a # 2 phillips screw driver, turn the Dog-Ear fastening screws clockwise (be sure to support the weight of the speaker until all Doq-Ear screws are securely tightened). The Doq-Ear Clamps will rotate away from the speaker enclosure and begin to tighten against the mounting surface to secure the speaker as shown in DIAGRAM 6. Carefully route the speaker wires to the amplifier or other power source. Be sure to avoid moving parts, heat producing items and water exposure. Note: To ensure your total surround sound experience, be sure to consider the SW10 and SW12 powered subwoofer system which will provide heart pounding bass to your favorite action movies. For the ultimate in Hi Fidelity sound quality, check out the MB QUART 5. 1 speaker systems (tower speakers, center channel and book shelf speakers) in several classic and modern finishes. DIAGRAM 4 RIGHT FRONT RIGHT REAR CENTER 5. 1 or 7. 1 System LEFT FRONT LEFT REAR 4 5 To amplifier or surround sound receiver 8-Ohms DIAGRAM 5 Dog Ear Clamp (1A) (1B) Dog Ear Clamp DIAGRAM 6 Drywall Dog Ear Screw Note: As you turn the Dog-Ear screws clockwise, the Dog-Ear Clamps will swing out away from the speaker (1A). Continue to turn the screw and the Dog-Ear Clampss will Lower down until they reach the mounting surface (1B) ADDITIONAL INSTALLATION AND OPERATIONAL INFORMATION - If you do not have the installation cut-out template, the cut-out dimensions are also located on the speaker label located on the side of the speaker. You can also down load the template by going to our web site at: www. maxxsonics. com - The speaker trim bezels and grilles can also be spray painted. There is a paint shield located in the speaker kit to prevent from getting paint on the speaker cone. Tip: Do not use roll-on paint because it will fill-in the holes in the grille which will dramatically effect the sound quality. Be sure to paint the grille separate from the speaker and do not re-install the grille until the paint has dried. - You may order additional parts such as Dog-Ear Clamps, Grilles, Grille removal tools by contacting Maxxsonics at: www. maxxsonics. com In-Ceiling Speaker In-Wall Speaker Mid Range Speaker Angled Baffle Adjustment The Alexxa series speaker feature an angled baffle design which positions the speaker on a 30% angle to the speaker enclosure. This allows you to rotate the speaker enclosure so that the speaker cone is facing towards the listening area as shown on Diagram 4. This is ideal for cathedral or pitched ceilings or walls do not permit the ideal mounting locations. Or Or Or Tweeter Element Or Mid Range Speaker Tweeter Angle Adjustment The tweeter element can be swivelled to allow you to aim or point the tweeter towards the listening area as shown above. [. . . ] Valid only to the original purchaser, this warranty automatically terminates before expiration if the product is sold or otherwise transferred to another party. This warranty does not cover product sold AS IS or when sold WITH ALL FAULTS. This warranty does not cover abuse, damage, cosmetic damage or damage due to misuse, accidents, negligence, Acts of God, Commercial Use, or modification of, or to any part of the product. This warranty does not cover damage due to improper operation, maintenance or installation, or attempted repair by anyone other than MB QUART or a MB QUART dealer which is authorized to do MB QUART warranty work. [. . . ]