User manual MCINTOSH CR12

[. . . ] OWNERS MANUAL CR12 Audio/Video Multizone Control System 20 CR12 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Thank You, Please Take A Moment, Customer Service and Table of Contents Thank You For your decision to own this McIntosh CR12 Auido/Video Multizone Control System ranks you at the very top among discriminating music listeners. The McIntosh dedication to Quality, is assurance that you will receive many years of musical enjoyment from this unit. Please take a short time to read the information in this manual. [. . . ] Refer to on Page 5 for the Din plug balanced terminal connections. Also connect a cable from the CR12 Din Multi-Channel Amp connector to the matching connector on the amplifier to provide zone power control. the matching C39/MX130 video inputs. Connect the Audio Outputs from A/V source components to both the CR12 and C39/MX130 inputs using a Y adapter if necessary. For dedicated zone source components, connect their Audio, Video and Data outputs to the CR12 Zone Aux In connectors. Note: The A/V source signals used in a dedicated zone replace the Aux signal source selection and are automatically switched when a plug is inserted into the Data port. If no data cable is used, insert 1/8 inch mini Stereo phone plug, (with a lead connected from the tip to the ring), to activate the switching. 4. Connect a WK-3/WK-4 keypad, using 4 conductor shielded cable to a zone terminal connector or connect a WK-2 keypad or R649 wall sensor to a zone sensor connector with RG6 or RG59U coax cable. Connect the video outputs of A/V source components to the CR12 video inputs and the CR12 video outputs to McIntosh Multi-Channel Amplifier 8. Connect the Video Out to Mon to the Video input of a remote zone TV or monitor. Connect a DB25 cable from the CR12 Controller Input A Connector to the To Multi-Room Controller connector on a McIntosh Control Center. NOTE: The DB25 cable passes only the CD2, Tuner, Tape 1 and Aux audio along with matching Data, Sys Off and Power Control signals from the control center to the CR12. Zone 1 Room Monitor/TV 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 McIntosh Keypad Left Loudspeaker McIntosh PC-3 To AC Outlet Y Adapter McIntosh LD Player 8 To PC-3 AC Outlets 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 987654321 Right Loudspeaker Dedicated Zone Source Component To PC-3 AC Outlet McIntosh Tuner McIntosh Audio/Video Control Center How to Connect Additional CR12s How to Connect Additional CR12s As many as six CR12s can be cascaded to supply audio and video to a maximum of 24 zones. Cascaded CR12s can also be connected with a McIntosh Control Center, which adds two additional zones. Connect a DB37 shielded 37 conductor cable from the To Next Controller socket of the first CR12, to the Controller Input B of the second CR12. All Audio signals and the audio portion of A/V sources connected to the first CR12 will be sent down the cable to each succeeding CR12 to allow all remote zones to receive audio from all the Audio/Video sources. McIntosh MultiChannel Amplifier 2. Connect video cables from the video outputs of the first CR12 to the video inputs of the second CR12. Repeat the video connections in and out of each CR12. When cascaded CR12 systems are used with a McIntosh Control Center, connect the video outputs of the last CR12 to the matching video inputs of the control center First CR12 for Zones 1-4 McIntosh PC-3 To AC Outlet Second CR12 for Zones 5-8 McIntosh LD Player To PC-3 AC Outlet To Third CR12 LV Video Input McIntosh MultiChannel Amplifier To AC Outlet To Third CR12 Controller Input B 9 How to Connect the CR12 in a Stand Alone System How to Connect the CR12 in a Stand Alone System 1. Connect the CR12 power cord to a live AC outlet. Connect a McIntosh Power Controller to the CR12 using either the Din or Pwr Ctl (power control) connector and connect zone amplifier power cords to the appropriate outlets on the Power Controller. Connect a McIntosh multi channel amplifier with a DB25 computer type cable from the CR12 Multi-Channel Amp connector to amplifier input connector. Note: Both audio and zone power control pass through this cable. Discrete zone audio cables may also be used, either balanced or unbalanced. Refer to Page 5 for the Din plug balanced terminal connections. Also connect a cable from the CR12 Din Multi-Channel Amp connector to the matching connector on the amplifier to provide zone power control. sensor connector with RG6 or RG59U coax cable. Connect the video outputs of A/V source components to the CR12 video inputs and audio outputs to CR12 audio inputs. [. . . ] Acc On / Acc Off Press the Acc On push-button to turn power on of an source component connected to the CR12 System and programmed. If a McIntosh Remote Control Translator is connected, press the Acc Off. to turn power Off of an accessory component connected to the CR12 System. CD2, Tuner, PH/Aux and Tape 1 Press any of these push-buttons to select the desired audio signal source. [. . . ]