User manual MCINTOSH MA6300

[. . . ] Integrated Amplifier MA6300 Owner's Manual McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1. Install in accordance with the manufacturer's instructions. [. . . ] The four feet may be removed from the bottom of the MA6300 when it is custom installed as outlined below. The four feet together with the mounting screws should be retained for possible future use if the MA6300 is removed from the custom installation and used free standing. The required panel cutout, ventilation cutout and unit dimensions are shown. MA6300 Front Panel Always provide adCustom Cabinet Cutout equate ventilation for your MA6300. Cool operation ensures the longest possible operating life for any electronic instrument. Cabinet Do not install the Front MA6300 directly Panel above a heat genOpening erating component for Ventilation such as a high powered amplifier. If all the components are installed MA6300 Side View in a single cabinet, in Custom Cabinet a quiet running ventilation fan can be a definite asset Support in maintaining all Shelf the system components at the coolest possible operating temperature. A custom cabinet MA6300 Bottom View installation should in Custom Cabinet provide the following minimum spacing dimensions for cool operation. Allow at least 6 2" inches (15. 24cm) 5. 08cm Note: Center the cutout Horizontally on the unit. The Data Port Connections allow for the remote operation of basic functions using the MA6300 Remote Control. For additional information refer to "Connector and Cable Information" on page 4. Connect a Control Cable from the MA6300 POWER CONTROL Jack to the Power Control In on the McIntosh SACD/CD Player. Connect a Control Cable from the McIntosh SACD/CD Player Power Control Out Jack to the Power Control In jack on the McIntosh Tuner. Connect a Control Cable from the MA6300 CD1 DATA PORTS Jack to the McIntosh SACD/CD Player Data In Jack. Note: If the CD2 unbalanced Audio Inputs are used instead of the Balanced CD1 Inputs, then connect the Control Cable to the CD2 Data Port. 4. Connect a Control Cable from the MA6300 TUNER DATA PORT Jack to the McIntosh Tuner Data In (Tuner 1). Connect any remaining McIntosh Source Components in a similar manner. Note: With the addition of a McIntosh Power Controller and Remote Control Translator connected to the MA6300, any McIntosh Classic Components and/or non McIntosh Components connected to the MA6300 can be operated more conveniently. Contact your McIntosh Dealer for additional information. McIntosh SACD/CD Player McIntosh Tuner 8 How to Connect Audio Components How to Connect Audio Components 1. Connect a Balanced Audio Cable from the McIntosh SACD/CD Player Audio Outputs to the MA6300 CD1 INPUTS. Note: The unbalanced Audio Outputs from the McIntosh CD Player connected to the CD2 INPUTS may be used instead of the Balanced CD1 Inputs. 4. Connect an Audio Cable from the MA6300 TAPE OUTS to the Record Inputs of a Recorder and from the MA6300 TAPE INPUTS to the Recorder Outputs. Connect any remaining Source Components in a similar manner. 2. Connect an Audio Cable from a McIntosh Tuner 1 Fixed Outputs to the MA6300 TUNER INPUTS. Connect an Audio Cable from a Turntable to the PHONO INPUTS and the Turntable Ground Connection to the GND grounding post. McIntosh SACD/CD Player McIntosh Tuner Recorder Turntable OUT IN 9 How to Connect Loudspeakers Caution: The supplied AC Power Cord should not be connected to the Rear Panel of the MA6300 Amplifier until after the Loudspeaker Connections have been made. [. . . ] Disc, Server and Tape Functions Use these push-buttons to operate a DVD Player, CD Player, CD Changer, Music Server or Tape Recorder. Numbered Push-buttons Press Push-buttons 0 through 9 to access tuner station presets, tracks on discs or selections on a Music Server. Disc and Track Use the DISC and TRACK Push-buttons when a Disc Player or Music Server is being used. Tuner Push-buttons Press the AM or FM Push-button to select the desired broadcast band. [. . . ]