User manual MCINTOSH MCD1000 CD TRANSPORT

[. . . ] CD Transport MCD1000 Owner's Manual McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. No user serviceable parts inside. CAUTION - Invisible Laser Radiation when open. [. . . ] Connect the MCD1000 Power Cord to a live AC outlet. McIntosh MDA1000 D/A Converter To AC Outlet 9 Front Panel Indicator, Push-Buttons and Switch Open and Close the Disc Door for loading or unloading discs IR Sensor receives commands from a remote control Power Switch turns all AC power completely On or Off Disc Tray opens to permit the loading and unloading of a disc Front Panel Display Standby Power On Light Move back one track at a time Stops disc Playback Standby/On Pushbutton turns the MCD1000 On or Off (Standby) Use to pause during Playback Move forward one track at a time Starts disc Playback 10 Front Panel Display Indicates the Program Track Play Mode is active Indicates the Number of Tracks and the Total Playing Time of the Disc when the player is stopped Indicates the number of tracks on the disc and the Program Step Number(s) Indicates Track Number Indicates the current Track Time, Remaining Track Time, Total Disc Playing Time and various Programming information Indicates when the Time Display is showing the Remaining Time Indicates the Random Track Play Mode is active Indicates when in the Pause Mode Indicates when the first ten seconds of each track is being played Indicates when in the Play Mode Indicates when the Repeat All Play Mode is active Indicates when the A-B Repeat Play Mode is active 11 Remote Control Push-Buttons Press a Number Push-button to select the desired Track Press the Up or Down Push-button to adjust the volume level of the MDA1000 Press the Input push-button followed by pressing one of the Numbered Push-Buttons to select the desired Digital Input of the MDA1000 Use to Program specific tracks for playback Press to move rapidly backward through a Track on the Disc Press to move rapidly forward through a Track on the Disc Press to sample the first 10 seconds of each Track on the Disc Press to Repeat various Playback Modes Press to Stop Disc Playback at any time Press to display the Current Track Time, Elasped Time or Total Disc Time Move forward one Track at a time Move backward one Track at a time Press to activate Random Track Playback Starts Standard Disc Playback and Program Playback Press to Pause Disc Playback at any time Notes: The Remote Control illustrated above is supplied with the matching MDA1000 D/A Converter. It is also available as an accessory for the MCD1000, check with your McIntosh Dealer for additional details. The buttons with the "small text descriptions" are used to control various functions of the McIntosh MDA1000 D/A Converter. 12 How to Operate the Remote Control How to Operate the Remote Control Numbered Push-buttons Press a NUMBER Push-button (1 through 9) followed by pressing the PLAY Push-button to directly access the desired disc track. Track numbers above 9 require the pressing of two NUMBER Push-buttons. If the desired Track Number is higher than 9, first press and hold down the NUMBER Push-button until the number entered shifts its position to the "Tens Digit", as indicated on the Front Panel Aphanumeric Display, followed by pressing the NUMBER Push-button for the "Units Digit". Program The PGM(Program) Push-button is used to enter desired Track Selections into memory for Playback. Refer to page 17 for additional information on Programming. Intro Press the INTRO Push-button to audition the first 10 seconds of each track on the CD Disc. Random Press the RANDOM Push-button to playback Tracks in a random order. Repeat Press the REPEAT Push-button to allow continuous playback of Standard Play Mode, Random Play Mode or Program Play Mode. Play Press the PLAY Push-button to start Playback of the currently selected disc or a stored Program. Time During standard Disc Playback, pressing the TIME Push-button will allow the Front Panel Alphanumeric Display to indicate either the Current Track Time, Track Elapsed Time, Track Remaining Time, Disc Elapsed Time, Disk Remaining Time or only the Track Number. Note: These five Track/Time Display Modes are not available during Intro Play Mode, Random Play Mode and Program Playback. Back and Next Press the NEXT Push-button to move forward or the BACK Push-button to move backward one track at a time. REV and FF Press the REVerse Push-button or FF(Fast Forward) Push-button to start moving rapidly through a track. Note: Audio level is automatically reduced during this operating mode. Stop Press the STOP Push-button to stop the disc playing. Alternate Remote Control Push-button Functions Most basic MCD1000 Operating Functions can be performed with Remote Controls of McIntosh A/V Controllers, A/V Control Centers or Preamplifiers and McIntosh Keypads. Additional MCD1000 functions can be performed with other McIntosh Remote Controls by using push-buttons that are labeled differently from the Compact Disc Remote Control. The chart below lists the MCD1000 operations that can be performed by these different pushbuttons on Remote Controls of other McIntosh products. Other McIntosh Remote Control Devices MCD1000 Function A/V Control Center WK2 Keypad WK3 Keypad WK4 Keypad Play Stop Pause Next Back Play Stop Pause Next Back Play Stop Next Back Seek Up Play Stop Play Stop - Next - Next Back Channel Up Channel Down Numbers 0-9 Fast Forward Fast Forward Fast Reverse Fast Reverse Seek Down Numbers 0-9 Numbers 0-9 Numbers 0-9 Pause Press the PAUSE Push-button to momentarily stop Playback operation at any time. Press the PLAY Push-button to resume Playback of the disc. 13 How to Operate the MCD1000 Press the POWER switch to ON, the Red LED above the STANDBY/ON Push-button lights to indicate the MCD1000 is in Standby Mode. To Switch On the MCD1000 press the STANDBY/ON Push-button. With no CD Disc loaded in the CD Transport the Front Panel Alphanumeric Display will indicate "Track 0" Refer to figures 1 and 8. Notes: For normal operation, switch the MCD1000 On and Off with the Standby/On Push-button. If the Disc Player is not going to be used for an extended period of time, turn Off all AC Power with the Power Switch. When the MCD1000 Power Control Jack is connected (via a cable) to a McIntosh MDA1000 D/A Converter, Control Center, A/V Multizone System Controller or Preamplifier, the MCD1000 will automatically switch ON and OFF with the system. When power is first applied, the MCD1000 will determine if a disc is present inside and during that time the OPEN/CLOSE Push-button is not active until a triangle appears on the Alphanumeric Display. Figure 2 Disc seated in the tray Figure 3 Figure 1 Notes: For immediate playback of the Disc press the PLAY Push-button instead of OPEN/CLOSE Pushbutton. [. . . ] Then display will indicate the track number, the First Program Step Number " 1 " is now on continuously and a flashing Second Program Step Number " 2 " will appear. 1. Press the PGM (Program) Push-button on the Remote Control to activate the Programing Mode on the MCD1000. Press the PAUSE Push-button and the first track of the stored program will start playing. To change the first progam track use either the NEXT and BACK Push-buttons or the NUMBER (0 thru 9) Push-buttons to select the new track and then press the PGM Push-button to enter it into the current memory location. Note: If the first program track selection doesn't need to be changed, just press the PGM Push-button and the second Program Step Location will become available for changing. [. . . ]