User manual MCINTOSH MDLP1

[. . . ] Video Projector MDLP1 Owner's Manual McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1. Install in accordance with the manufacturer's instructions. [. . . ] Press the STANDBY/ON Pushbutton on the Projector Control Panel or the PROJ ON Push-button Figure 13 using the Remote Control. Temporarily place the previously removed protective cover onto the projector lens. Remove the AC Power Cord from the projector. Proceed to the "How to connect the MDLP1" on page 17. Figure 11 15 Rear Panel Connections and Switch DATA IN Port receives signals from McIntosh A/V Control Center for Remote Control Operation TRIGGER 1 Output sends a Turn-On signal to other components when the MDLP1 is switched On COMPONENT INPUTS receive Component Video (Y, PR and PB) Signals from Component Video Sources POWER CONTROL IN receives turn-on signals from a McIntosh component and POWER CONTROL OUT sends turn-on signals on to another McIntosh Component TRIGGER 2 Output sends Turn-On signals to other components and may be assigned to activate when a specific aspect ratio is selected. RS232 connector for connection to a computer or other control device Connect the MDLP1 power cord to a live AC outlet. Refer to information on the back panel to determine the correct voltage Switches Off the illumination to the Top Control Panel McIntosh Logo IR INput for connecting an IR Receiver HDMI Inputs receive digital video signals from a McIntosh A/V Control Center and/or other source components 16 How to Connect the MDLP1 How to Connect the MDLP1 The MDLP1 has the ability to automatically switch power On/Off to McIntosh Components via the Power Control and Trigger Connections. The Data Port Connections allow for the remote operation of the MDLP1 from other McIntosh Components. With an external sensor connected to the MDLP1, remote control operation is possible when the MDLP1 is located in an enclosure. The connection instructions below, together with the AP1000/MDLP1/VP1000 Input and Control Connection Diagrams located on the separate folded sheet "Mc2A and Mc2B", are an example of a typical audio/video system. Your system may vary from this; however, the actual components would be connected in a similar manner. For additional information refer to "Connector and Cable Information" on page 6. Note: With the addition of a McIntosh Power Controller connected to the MDLP1, AC Power Switching can additional information. If the MDLP1 is connected to a McIntosh Audio/Video Control Center MX136, MX135, MX120, MX119, or MX134 (MX Series) add the following connection: 6. Connect a Video Cable from the MDLP1 Y1, PB1 and PR1 COMPONENT VIDEO Input Jacks to the McIntosh MX Series Component Video MON A Jacks. Connect a Video Cable from the MDLP1 HDMI 1 Input Jack to the McIntosh MX Series HDMI MON A Output Jack. Note: Only the MX136 and MX120 Audio/Video Control Centers will have a HDMI MON A Jack. Connect the MDLP1 AC Power Cord to a live AC outlet. Connect the remaining components' AC Power Cords. be provided to components such as a motorized projection screen. Contact your McIntosh Dealer for Power Control Connections: 1. Connect a Control Cable from the MDLP1 POWER CONTROL IN Jack to the Power Control Out A Jack on the McIntosh VP1000 Video Processor. If the MDLP1 is connected to a McIntosh Audio/Video Control Center MX136, MX135, MX120, MX119, MX134 or MX132 (MX Series) add the following connection: 2. Connect a Control Cable from the MDLP1 POWER CONTROL IN A Jack to the McIntosh MX Series Power Control Zone A Out Jack. Data Control Connections: When the MDLP1 is connected to the McIntosh VP1000 Video Processor no Data Port connection is necessary. If the MDLP1 is connected to a McIntosh Audio/Video Control Center MX136, MX135, MX120, MX119, MX134 or MX132 (MX Series) add the following connection: 3. Connect a Control Cable from the MDLP1 DATA IN Jack to the McIntosh MX Series SUM A Data Port Jack. [. . . ] With a given Trigger 2 (Full, How to Operate the MDLP1, con't Normal, Zoom, V-stretch and Through) set to ON a 12VDC output will appear at the Trigger 2 Output Jack; when set to OFF, 0V appears at Trigger 2 Output Jack. Remote Control - Selection includes the two built in sensors along with any external sensor(s) connected via the external IR Input Jack or just external sensor(s). Refer to page 5, General Information Note 6. Wireless: Selects external sensor(s) only. [. . . ]