User manual MCINTOSH MHT200

[. . . ] A/V System Controller MHT200 Owner's Manual Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc. McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. [. . . ] Attach the hookup cable with connectors to the microphone, making sure the cable end with the locking collar attches to the microphone, and place the microphone into the stand adapter, with the stand adapter attached to a suitable microphone stand. Switch the Power On to the Microphone by moving the slide switch towards the color dot. Press and hold the Front Panel SETUP Push-button for approximately three seconds. The word SETUP will appear on the Front Panel Display and the MAIN SYSTEM SETUP Menu will appear on the Monitor/ TV screen. Using the Up or Down directional push-buttons select Speaker Setup on the On-Screen Menu, followed by the SELECT Push-button on the Remote Control. Refer to figure 21 on page 31. Note: It is extremely important to have the room as quiet as possible where the testing is occurring (temporally switch off TVs, heating/cooling equipment and radios, etc. ) as this will yield the most accurate results. The Subwooofer Settings allow for optimizing performance in the Home Theater System that relate to Room Acoustics and Loudspeaker Characteristics. For most Systems the default setting will produce the best performance. Refer to the Owner's Manual that came with the Loudspeaker, your Dealer and/or the manufacturer of the Loudspeaker for recommendations. A chart on page 35 has been provided to record the Subwoofer Settings. Note: Before adjusting the SUBWOOFER SETTINGS, you FIRST must have performed the SPEAKER SIZE, SPEAKER TIME DELAY and SPEAKER LEVEL Adjustments. 1. Press and hold the Front Panel SETUP Push-button approximately three seconds to enter the Setup Mode. The word SETUP will appear on the MHT200 Front Panel Display and the MAIN SYSTEM SETUP Menu will appear on the Monitor/TV screen. Using the Up or Down directional push-buttons select Subwoofer Settings on the On-Screen Menu, followed by the SELECT Push-button on the Remote Control. Note: The first time the SUBWOOFER SETTINGS is accessed, the default settings will be indicated. 6. Using the Up or Down directional push-buttons select AUTOCALIBRATE DELAYS on the On-Screen Menu, followed by the SELECT Push-button on the Remote Control. The Automatic Calibration Mode of the MHT200 will go through many tests for each of the active Loudspeaker Channels. The On-Screen Display will provide a status update of the testing as it progresses. The On-Screen Display will indicate when testing is complete. Continue next to the SUBWOOFER SETTINGS. If you do not wish to perform SUBWOOFER SETTINGS adjustments at this time, proceed to the next step. Select EXIT from the SPEAKER SETUP Menu. The MAIN SETUP Menu will reappear on the Monitor/TV screen and select EXIT from the Menu. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. The MHT200 will then return to normal operation. [. . . ] When a station is selected, the Front Panel Alphanumeric Display will indicate (from left to right) Station Signal Strength from 1 to 9, a dot if the Broadcast is Stereo, the AM/FM Station Frequency, AM or FM Broadcast Band and a Preset Number (if that station has been assigned a Preset). Figure 87 Figure 86 64 How to Optimize AM Reception 6. Press the numbered push-button corresponding to the Station's Preset Number. Press and release the REVIEW Push-button to review all of the available presets stations, press the REVIEW Push-button a second time to stay on the current Preset. Note: FM Broadcast Band Indications are in Megahertz, in the US and Canada, and change frequency in 100kHz steps. The second digit to the right of the dot which displays a 0, is used for FM stations in various locations other than the US where stations change in 50Hz steps. [. . . ]