User manual MCINTOSH WS350

[. . . ] Installation Guide In-Wall Loudspeaker Systems WS320 WS350 WS320 WS350 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Installing the Loudspeaker The WS320 and WS350 In-Wall Loudspeaker Systems require at least 3-3/4 inch of wall depth, including the wallboard. They can be mounted into a wall surface with a thickness between 3/8 inch and 1 inch. [. . . ] Pull enough Loudspeaker Cable to be able to connect it to the Loudspeaker Baffle while the baffle is still out of the wall. Install the two L Shaped self adhesive Frame Gaskets to the rear of the frame so that it will be between the frame and the wall. Insert the right side of the assembly into the hole and push it to the right. This will give enough room to insert the left side of the assembly into the wall. Center the assembly in the opening. 2 4. Push the right side Clamping Piece up against the backside of the wallboard. Tighten the now protruding center screw enough to gently hold the frame in place. Use the bubble level to assure the frame is correctly positioned, and then tighten all the screws until the frame is securely attached to the wallboard. Note: To avoid crushing the wallboard, do not over tighten the screws. If the mounting position places the frame near a stud, remove the clamping piece and secure the frame directly to the stud, through the provided holes. Installing the Baffle Box Before setting the Baffle Box into the frame, run the Loudspeaker Wire through the supplied Airtight Electrical Connector and tighten the connector onto the Loudspeaker Cable. Be sure to pull enough wire through the connector to allow connection to the crossover network on the back of the Loudspeaker Baffle while it is still out of the wall. Set the Baffle Box into the frame. Note: The Baffle Box may be positioned with the Airtight Electrical Connector either at the top or bottom. Connecting the Loudspeaker The McIntosh WS320 and WS350 In-Wall Loudspeaker Systems utilize Binding Posts for Loudspeaker Cable Connections. Connect a Loudspeaker Cable from the black or negative Loudspeaker Binding Post on the back of the Loudspeaker Baffle to the negative or common output terminal of one channel of the amplifier. [. . . ] 2 Chambers Street Binghamton, New York 13903 Phone: 607-723-1545 Fax: 607-723-3636 Serial Number: Purchase Date: Dealer Name: WS320 Performance Specifications Driver Complement 8 inch Woofer 1 inch Dome Tweeter Impedance 4 ohm Nominal Frequency Response 60Hz - 20kHz + 2dB (Anechoic Response) Sensitivity 86dB (2. 8V/1m) Crossover Frequency 1. 5kHz Power Handling 200 Watts Maximum Dimensions 23. 5 inches (59. 7cm) Height, 14 inches (35. 5cm) Width, 3. 65 inches (9. 3cm) Depth Finish White Primer Coat Weight (each) 22 pounds (10kg) net, 29 pounds (13. 2kg) in shipping carton WS350 Performance Specifications Driver Complement 8 inch Woofer 4 inch Midrange Five 1 inch Dome Tweeters Impedance 4 ohm Nominal Frequency Response 60Hz - 20kHz + 2dB (Anechoic Response) Sensitivity 85dB (2. 8V/1m) Crossover Frequencys 300Hz and 1. 5kHz Power Handling 200 Watts Maximum Dimensions 23. 5 inches (59. 7cm) Height, 14 inches (35. 5cm) Width, 3. 65 inches (9. 3cm) Depth Finish White Primer Coat Weight (each) 25 pounds (11. 3kg) net, 32 pounds (14. 5kg) in shipping carton McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 Copyright 2001 ã by McIntosh Laboratory, Inc. McIntosh Part No. [. . . ]