User manual MEDION BLOOD PRESSURE MONITOR MD 15231

[. . . ] Introduction 1 Congratulations on choosing to buy a health+ product. By doing so you now have the assurance and peace of mind that comes with purchasing a product made by one of Europe's leading manufacturers. All products brought to you by health+ are manufactured to the highest standards of performance and safety, and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 3 Year Warranty. Please fill in and return the Warranty Card to the address provided. General information 2 · Please read these operating instructions thoroughly and follow them and the safety notes in particular before using the appliance for the first time! [. . . ] Insert two 1. 5V batteries size AAA/LR03 (alkaline). Pay attention to the polarity (the negative terminal faces the spring). Close the battery compartment. Replace the batteries · if the battery icon appears on the display, · if the display remains blank after pressing the ON/OFF button. Replace all batteries with new batteries of the same type at the same time. Do not mix used and new or different types of batteries together. Rechargeable batteries are not suitable for the operation of this device. 14 Setting the date and time 1. Press the buttons and M at the same time. Press the M button repeatedly to set the current month. Press the M button repeatedly to set the current day. Press the M button repeatedly to set the current hour. Press the M button repeatedly to set the current minutes. The flashing bar disappears after 10 seconds. Press the button to finish the date and time setting. The device closes the setting mode automatically after one minute. 15 Usage 1. Attach the wrist sleeve in such a way that it is approx. 5 ­ 10 mm away from the palm of your left hand (see fig. Ensure that no articles of clothing are trapped in the sleeve. Hold the lower part of the sleeve as shown in fig. Pull down and wrap it around and upwards, so that there is no gap between the sleeve and your wrist. Use your thumb to hold the sleeve cover while you wrap it upwards. Wrap the sleeve according to the shape of your wrist. If the sleeve is not firmly attached the pressure will increase and the wrist will become numb. Correct measurement is then no longer possible. 16 7 If the sleeve cannot be attached to your left arm and if it is not possible to measure your left arm, use your right one. [. . . ] The device corresponds with standards EN 1060-1: 1995 and EN 1060-3: 1997 for non-invasive blood pressure measuring devices. Type B The device was manufactured in 2008. 0197 The serial number is arranged inside the battery compartment. 28 Appendix Table 201 13 Guidelines and manufacturer's declaration ­ electromagnetic emissions Model MD 15231 is designed for operation in an environment as described below: The customer or user of Model MD 15231 should ensure that it is operated in such an environment. In line Interference with emission measurements HF emissions according to CISPR 11 Group 1 Electromagnetic environment guidelines Model MD 15231 uses HF energy exclusively for its internal operation. Therefore its HF emission is very low and it is unlikely that nearby electronic devices should suffer interference. 29 Interference emission measurements In line with Electromagnetic environment ­ guidelines HF emissions according to CISPR 11 Class B Emission of harmonics according to IEC 61000-3-2 Emission of voltage fluctuations/flicker according to IEC 61000-3-3 Not applicable Model MD 15231 is intended for use in all premises including residential areas and those that are directly connected to public supply networks that also supply buildings that are used for residential purposes. Not applicable Table 202 Guidelines and manufacturer's declaration ­ electromagnetic interference immunity Model MD 15231 is intended for operation in an electromagnetic environment as described below: The customer or user of Model MD 15231 should ensure that it is operated in such an environment 30 Interference immunity tests IEC 60601test level Pass level Electromagnetic environment ­ guidelines Electrostatic discharge (ESD) according to IEC 61000-4-2 ± 6 kV contact discharge ± 8 kV air discharge N± 8 kV Floors should be of wood or Air discharge concrete or laid with ceramic tiles. If the floor is covered with synthetic material, the relative humidity should be at least 30%. [. . . ]