User manual MEDION GOPAL 4.5 QUICK GUIDE

[. . . ] Software manual GoPal Navigator Version 4 GoPal Navigator Version 4 Contents CHAPTER 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Greeting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Contents of CD/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Deactivate Auto OFF If you tap the option Deactivate Auto OFF in the list, Auto Off mode is not executed: The device remains switched on regardless of the status of the power supply until the internal voltage has been exhausted. In this case, the settings you set in Power Management (see previous page) are valid. · 1 Minute When you tap the option 1 Minute in the list, the device is automatically switched off 1 minute after the plug has been pulled out. 2 Minutes When you tap the option 2 Minutes in the list, the device is automatically switched off 2 minutes after the plug has been pulled out. 5 Minutes When you tap the option 5 Minutes in the list, the device is automatically switched off 5 minutes after the plug has been pulled out. · · If you did not select Deactivate Auto OFF, your navigation device displays the following screen after the power supply plug has been pulled out. 25 Adjusting the settings · · · The The The button returns you to the screen that was active before the plug was pulled out. button restarts the device. Note Please be aware that this function is only available on certain types of device. FM transmitter Further information about the FM transmitter settings can be found in the device manual. Note Please be aware that this setting is only available on certain types of device. Restore factory settings This button allows you to restore the factory default settings to the device. All personal settings such as favourites or the last entered destinations are deleted in the process: Accordingly, you should only perform this function when you no longer need this information. When you tap the button, a confirmation message pops up on your navigation device. Tap the button to restore the factory settings: Otherwise you can cancel the process with the button. When you tap the button, the device is restarted and the following settings are reset: After the restart you must then select the language within the software. In addition, you have another opportunity to familiarise yourself with your navigation system by way of a brief introduction after the navigation software starts: You can also skip this step and start operating your navigation system immediately, as required. Specific settings for the navigation software Following start-up your navigation system functions with standard settings which can, however, be changed and adapted to your personal needs in the Settings menu at any time. Open the Settings menu by pressing the button, available on the main screen of the menu view. Tip If you want to accept the default settings of your navigation system or have already made your personal settings, you can skip the following pages and go directly to Chapter 6, ® Operating the GoPal navigation software. Choose from the following setting menus: · · · · Route options Display Language settings Device settings 26 Adjusting the settings · · Program settings Help The following describes the available setting menus as well as the setting options available there. You can change the chosen settings again at any time. Adjusting the route options This sub-menu allows you to adapt the route calculation and navigation to your current personal needs. Note that the route options can affect each other: Depending on the selection of route type, other route options will be automatically deactivated. The following options are generally available for selection: · Route calculation has been optimised for cars. Road traffic regulations are in effect for this setting: This means that all roads may generally be used; however one-way streets may only be driven on in the proper direction of travel. As a rule, pedestrian zones are not directly accessible and a corresponding message is emitted. As an alternative to the setting you can choose one of the following options: o Route calculation has been optimised for Bicycle (possible in a radius of up to 50 km from the current position): Cycling paths have also been taken into account when calculating the route, pedestrian zones are directly accessible. The shortest route is always calculated and the traffic jam detour function is generally not active. The use of motorways and toll roads is excluded; the corresponding route options are automatically deactivated (see later section). Route calculation has been optimised for Pedestrians (possible in a radius of up to 50 km from the current position): Footpaths and cycling paths have also been taken into account when calculating the route; one-way streets can be used in both directions of travel and pedestrian zones are directly accessible. [. . . ] In addition to the visual navigation, all manoeuvres are also announced using voice commands. You can adjust the voice output during navigation as follows: · button in the upper left area of the screen: The setting menu Volume then opens, Tap the which allows you to individually set the volume for voice output, the key click and audio playback of MP3 files using the additional MP3 Player application. The volume set here applies equally to playback via the internal speakers and via the earphone connection (3. 5 mm mini jack) on your navigation device. o The buttons and allow you to individually lower or raise the volume for the respective signal output in six steps. [. . . ]