User manual MEDION MD 20220 CODE LIST

[. . . ] Contents Information about these instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The symbols and signal words used in these Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Use in accordance with regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press this button again if you wish to leave the OSD. + + Power block, when the OSD is not activated OSD block, when the OSD is not activated Hold the key combination until the bar displayed has moved from left to right completely, to activate/de-activate the block. A corresponding message will appear on the screen. Select a parameter and reduce its value with this button, when the OSD is switched on. If you are not in the OSD: Direct call-up of the Contrast/Brightness menu. Select a parameter and increase its value with this button, when the OSD is switched on. If you are not in the OSD: Direct call-up of the OptiColor Mode menu. Operational display Confirm the selection of the parameter to be changed with this button. If you are not in the OSD: Direct call-up of the Automatic adjustment. You can switch the TFT monitor on or to the Standby mode with this button. UK/ N. IRELAND HELPLINE 0871 3761020 (costs 7p/min from BT landline, mobiles costs may be higher) REP. IRELAND HELPLINE 1-800-992508 13 Changing the parameters of the TFT monitor The On Screen Display (abbreviation: OSD) is a menu that is briefly faded in across the TFT monitor. You will be able to set certain parameters of the TFT monitor through the OSD menu. Operating the OSD menu 1. Press the button, in order to activate the OSD. Select the options from the Main Menu with the 3. Press the button. button, in order to leave the OSD. The OSD will be faded out automatically if you have not operated any button on the TFT monitor for the pre-set time. The OSD menu The main functions or possible settings through the OSD are explained in the following. (Ill. : OSD menu) Important!The menus described here can differ from those on your monitor because of possible technical changes. 14 UK/ N. IRELAND HELPLINE 0871 3761020 (costs 7p/min from BT landline, mobiles costs may be higher) REP. IRELAND HELPLINE 1-800-992508 Menu point Function / sub-menu Automatic adjustment: Sets the horizontal and vertical position, phase (fine tune) and clock cycle (H size) automatically. Contrast: Sets the white value of the monitor foreground. Brightness: To adjust the brightness of the video. [. . . ] Type 2: Pixels not shining (dark, black point), although activated Type 3: Abnormal or defective sub-pixels coloured red, green or blue (e. g. shining for a long time with half brightness, not lighting one colour, flashing or flickering, but not Type 1 or 2) Addition: Cluster of Type 3 (= failure of two or more sub-pixels in a block of 5 x 5 pixels. A cluster is a field of 5 x 5 pixels (15 x 5 sub-pixels). Classes of pixel error: Error Class I II III IV Type 1 0 2 5 50 Type 2 0 2 15 150 Type 3 0 5 50 500 Cluster of Type 3 0 2 5 50 The permitted number of errors of the types specified above in each class of error relates to a million pixels and must be converted in accordance with the physical resolution of the display. [. . . ]