User manual MEDION TFT DISPLAY MD 30820

[. . . ] Contents: SAFETY INSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Purpose of use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] or · Start the "Display" program in "System control". The resolution can be set under "Screen resolution". Your monitor can display a maximum of 1680 x 1050. Then click "Color quality" ( )to set the color depth (number of colors displayed). Your monitor supports a maximum color depth of 16 million colors corresponding to 32 bit or "True Color". This resolution is equivalent to the physical resolution. TFT screens reach their full image quality at their physical resolution. The image repeat frequency can be set under "Advanced" ( ). A window with the characteristics of your video card appears depending on the configuration of your computer. Under "Adapter" you can change the desired value in the selection field "List All Modes. . . ". The value for the LCD should be 60 Hz and, depending on the setting, not exceed 75 Hz. (similar picture) Attention!If your setting does not coincide with the values supported by your display, you may not see any image. Switch your old device on again and set the applicable values under `Display Characteristics' in accordance with the aforementioned options in this case. START-UP 7 Unpacking 1. Please keep the packaging material well and use it exclusively to transport the monitor. Screws to attach the base plate will be in the packaging. Keep them away from children; there is a danger of swallowing them. Installing the base plate 1. Place a soft, clean pad under the monitor, so that it will not be possible for the surfaces to be scratched or damaged. Place the monitor with the back on a flat and stable surface. Position the base plate on the foot of the monitor. Use a coin or a slot screwdriver and attach the base plate with the screws supplied. Connecting the Monitor To start using the LCD monitor straight away, please read the "Safety Instruction" section (page 1). We recommend that you also read all the other sections as these contain detailed explanations and tips on how to use your LCD display. Ensure that the LCD monitor is not yet connected to the line power (power cord not yet plugged in) and neither the LCD monitor nor the computer is switched on. Prepare your computer for the LCD monitor if necessary (see previous pages) with the correct settings for your LCD. I 0 8 ENGLISH Connecting VGA Signal Cable 3. Plug the signal cable into the matching VGA sockets on the computer. [. . . ] · Type 3: Abnormal or defective red, green or blue sub-pixels. constantly lit with half the brightness, one color is not shining, blinking or flickering, but not belonging to Type 1 or 2 Pixel Failures). In addition: A cluster of type 3 (= 2 or more defective sub-pixels in an array of 5 x 5 pixel). A cluster is an array of 5 x 5 pixel (15 x 5 sub-pixel). [. . . ]