User manual MEDION USB 2.0 FLATBED SCANNER MD 90009

[. . . ] Content: SAFETY AND SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Point of use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Connecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] of bank notes) can violate domestic or international law and be subject to severe penalties. In questions of doubt please consult a lawyer. Box includes Please check the contents of the box. Notify us within 14 days of purchase if your flat bed scanner is not complete. Your box includes: · · · · · · · USB flat bed scanner unit Transparency Adapter USB cable AC Adapter (HDAD15W101-126) Installation and application software on CD This user manual Guarantee document System requirements · · · · · · · Computer Processor type and speed Operating system Memory Hard disc capacity Installation Connections PC/AT compatible computer Pentium III class 500 MHz or higher Windows®98SE/ME/2000/XP 64 MB, recommended: 128 MB or more min. 800 MB free storage capacity CD-ROM drive USB interface 6 Introduction SETUP 1. During software installation your important files can be changed or deleted. To avoid problems in using older files after installation, make sure you backup your hard disk. Connecting to the power supply Diagram for illustration purposes only: 1. Observe the notes in chapter "Safety and Service" (page 1). Position the computer and scanner so that you can work with them easily and safely. Connect the supplied power adapter to your scanner as shown in the diagram above. Connect the power adapter to a power socket in close proximity of your flat bed scanner. Setup 9 4. Connecting to the PC Connect your flat bed scanner as follows: Make sure your scanner software has been installed already (see page 7). Power on/off 1. Switch on the computer and all connected peripheral equipment (monitor, printer, external hard drive, etc. ) and wait until the operating system has booted completely. Connect one end of the USB cable ( ) to a free USB connection socket on your computer ( ) and the other end to the scanner. Press the On/Off switch on the control panel. Windows® will then recognise that a new piece of hardware has been connected and complete the installation procedure. Please note: If your operating system is configured so that the installation procedure accepts only signed drivers and software (the default) an information screen will appear. Although the software lacks the digital signature it may still work properly. Click on "Tell me why this testing is important" to get detailed information. Confirm by clicking on "Continue". 10 Setup OPERATION You will find new program groups and Help files on your computer when the software installation has finished. You will find the installed OCR program, which will make comprehensive documentation available to you through the online help. Scanning 1. [. . . ] If you require the scanned material for printout. A lower resolution is usually sufficient which decreases the size of the file. The file was stored in an uncompressed format (e. g. : BMP). File formats such as JPG can store images without noticeable loss of details and require only a fraction of the original storage space. [. . . ]