User manual MELICONI GUMBODY FACILE 100

[. . . ] The large keys are easy to see and to use. Keep this booklet in case you ever need to consult us in the future. For anyone with internet, via the website www. meliconi. com/guide, it is even easier and quicker to programme the remote control and discover all the potential of the FACILE 100 thanks to the on-line guide. USING THE KEYS AND FUNCTIONS The functions described below are only available if they are already foreseen by your TV. Teletext keys Number keys To select an external input terminal Light indicator TV ON/OFF key To select the next (P+) or previous (P-) channel or programme Control the volume using +/­ MUTE turns the volume on and off To move around within the MENU or to control the BRIGHTNESS/COLOUR Confirm key Key with additional TV functions Fastext functions or to select submenus by means of the colours Impact-proof rubber casing To access the MENU PREPARE FOR USE Read these instructions carefully before programming your remote control! 1 FITTING THE BATTERIES Before programming and using the remote control, fit the batteries. The remote control requires 2 new AAA/LR03 batteries. Insert the batteries as shown: · Change the batteries if the light indicator starts to flash during use. · When you remove the batteries, fit the new ones within 5 minutes or you may have to reprogramme your remote control. [. . . ] In this case, consult our website www. meliconi. com/guide GLOBAL SEARCH REMOTE CONTROL PROGRAMMING This operation can take up to 20 minutes and should be carried out if you have not succeeded in programming the remote control by means of the method described above. The quickest and easiest way to programme the remote control is by consulting the website www. meliconi. com/guide. 1. Hold down the MUTE and ON/OFF keys together for 5 seconds until the light indicator starts to flash indicating that the remote control is being programmed. Release the keys and enter the code 0000 within 12 seconds. The light indicator flashes more quickly to indicate that the remote control is ready for the search. Press and slowly release the ON/OFF key several times, stopping when the TV goes off. When the TV goes off, press the OK key to confirm. Three flashes indicate that the operation has been completed correctly. + 5 SEC. + + + ADDITIONAL CHECK Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar remote control but not the right one. In this case, repeat the search procedure starting from point 2. To display and make a note of the code memorized by means of the search, follow the instructions described in the paragraph CURRENT CODE DISPLAY. N. B. The remote control exits programming mode and the light indicator stops flashing: · if no keys are pressed for 14 seconds · if the end of the code search list has been reached. In this case, consult our website www. meliconi. com/guide 3 CURRENT CODE DISPLAY To find out the code of your remote control, follow this procedure: 1. Hold down the MUTE and ON/OFF keys together for 5 seconds until the light indicator starts to flash. Release the MUTE and ON/OFF keys and press and release the 1-/-- key within 8 seconds. After a few seconds, the light indicator communicates the code you are looking for by flashing the four numbers separately. Count the number of flashes; each series of flashes corresponds to one figure in the code. Make a note of the code on the adhesive label inside the battery cover for quick and easy future reprogramming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . = 6 Code obtained = 1306 + 5 SEC. N. B. this operation cannot be interrupted and the remote control cannot therefore be used until the end of the 4 series of flashes. ENTERING THE CODE If you know the exact code with which to programme the remote control, enter it as follows: 1. [. . . ] Reset the remote control code, following the programming procedure. The code for your appliance make is not in the Code Book. To find the code with which to programme your remote control consult the on-line guide at www. meliconi. com/guide INFO-LINE If you have any queries about your FACILE 100 remote control: · read this Instruction Booklet carefully - you will find an answer to most of your questions · consult the website www. meliconi. com/guide where you will find the answers you need easily and quickly. WARRANTY: 2 years The warranty ceases to be valid if the product is tampered with or used incorrectly. Remote control type GumBody Model FACILE 100 Purchase date / / Dealer's stamp The symbol of the crossed trash can shown on the remote control indicates that once the product has reached the end of its working life it should be disposed of separately from other waste. The user should, therefore, take the remote control to a specialised collection centre for electronic and electrical waste, or hand it over to the dealer when purchasing a new similar remote control, on a one to one basis. Correct separated collection for subsequent recycling, processing and environmentally compatible disposal contributes in preventing possible negative effects on the environment and on health and favours the recycling of the materials used in producing the remote control. [. . . ]