User manual MEMOREX MC2850-03OM

[. . . ] FILE/TIME Button 3 LOCATION OF CONTROLS REAR 1 2 3 4 1. 4. MIC SENS (Microphone Sensitivity) Switch VOX Switch HOLD Switch Battery Compartment 4 BATTERY INSTALLATION 1 Open the battery compartment by sliding it towards the bottom of the unit. 2 Insert two (2) "AAA" size batteries (not included) following the polarity diagram. Slide the battery compartment back in place. NOTE: When replacing the batteries, the recorded messages will be saved, but the time will have to be reset. 5 BATTERY INSTALLATION BATTERY INDICATORS: : The batteries are fresh. [. . . ] After setting the minute, press the PLAY/STOP button 3 again and the date/time will be set. 4 While the date/time appears in the display, press the FILE/TIME button to select 12 or 24 hour time display. 1 8 OPERA OPERATION TO TURN THE UNIT ON & OFF 1 2 1 To turn the unit on, press the REC/STOP 1 or PLAY/STOP 2 button. To turn the unit off, simply do not touch any button for 30 seconds, and the unit will automatically turn off and show the time. TO SWITCH BETWEEN MODES 1 3 2 3 1 1 To enter the Standby mode, press the REC/STOP button 1 or PLAY/ STOP button 2 while the unit is off (Time shows on display). To turn off the unit, press the MODE/PAUSE button 3 once while in the standby mode. 3 9 OPERA OPERATION ADJUSTING THE VOLUME 1 2 1 To adjust the volume, while in the Standby mode or during playback of a file, press the VOL+ 1 or VOL­ button 2 ; the volume number will increase or decrease to indicate the volume level (i. e. "0" is minimum and "15" is maximum). EARPHONE JACK For private listening, connect an earphone (not included) to this jack. The speaker is 3 automatically disconnected when the earphone plug is inserted in the jack. 3 10 OPERATION RECORDING QUALITY You can choose between four voice recording quality modes. For best sound quality, select HP (High Play), for very good sound quality, select SP (Standard Play) and for good quality, select MP (Medium Play). For longer recording time (reasonable sound quality), select LP (Long Play). 1 2 1 3 Press and hold the MODE/PAUSE button 1 for two seconds; "SET" will appear and the recording quality will blink. Press the REV 2 or FWD 3 button to select the desired recording quality. 1 11 OPERATION OPERATION 2 the desired recording quality When the desired recording quality appears, press the MODE/PAUSE button twice to confirm and turn the unit off (Time will show on the display) or the unit will turn off automatically if no button is pressed in 30 seconds. High Play: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 min. Standard Play: . . . . . . . . . . . . . . . . . . . . . . . . . . 275 min. · For normal voice levels, a distance of 5-9 inches is appropriate. 3 16 OPERATION VOICE ACTIVATED (VOX) RECORDING Voice activated recording will allow dictation only when you speak. When the unit detects a pause of a few seconds, it will temporarily stop recording until it detects sound again. 1 Slide the VOX switch on the rear of the unit to the ON position. Turn the unit on (by pressing the REC/STOP or PLAY/STOP button), and select the desired sound quality as described on page 11. 2 1 Select a File Folder by pressing the FILE/TIME button (see page 13). 17 OPERA OPERATION 3 Press the REC/STOP button and the REC indicator will light and the elapsed time will appear. Speak into the built-in microphone or insert a microphone into the MIC jack and when the unit picks up sound, it will record. When there is no sound, it will not recording, the REC indicator will blink and PAUSE will blink in the display until sound is detected. Press the REC/STOP button again to stop recording. NOTES: · The first few sounds activate the recorder and may not be recorded. · A variation in voice level during recording will not stop the unit, two seconds of silence is required to stop the recording. · For constant recording, see page 15. · To pause, press the MODE/PAUSE button. · The built-in audio level automatically sets the recording level. [. . . ] Press and hold the PLAY/STOP button 2 for 2 seconds; SCAN will appear in the display. The unit will automatically scan and play the first five seconds of each message in the selected file folder, starting at message one. 2 1 The unit will automatically stop after all messages have been played. To play back the message during scanning, press the PLAY/STOP button once to change to Playback mode. To stop Scan Playback, press the PLAY/STOP button twice. 23 OPERATION ERASING A SINGLE MESSAGE 1 2 3 1 While in the Standby mode, select the desired file folder using the FILE/TIME button 1, and the desired message to delete using the REV 2 or FWD 3 button; the message number and the message length will appear in the display. 2 Press the DEL/REPEAT button; ERASE will appear in the display and the first five seconds of the message will play. [. . . ]