User manual MEMOREX MPH-1089-4389

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Connect the straight cord to the base TELEPHONE LINE CORD and telephone jack as shown in Figure 1. Attach the supplied Wall Mount adapter to the rear of the telephone. Drill two holes with a vertical distance between the two marked positions of 83mm as shown in Figure 2. Tighten them to the end of the screw lines, only leaving the smooth part of the screw head outside the wall. Plug the telephone line cord into the modular wall jack. Reverse the position of the Wall Mount Hook on the base Figure 2 as shown in Figures 3 and 4. Hang the unit onto the screws, then slide it down firmly to fasten the base securely. When using this phone as a wall mount phone, be sure to route the short line cord on the back of the base unit and plug the other end into the wall mount jack. Figure 3 E6 Figure 4 MPH-1089-4389. O/M. QXD 5/25/01 11:34 AM Page 7 POWER SOURCES AC Power Adapter To operate the unit using AC power, connect the AC adapter to the DC jack on the rear of the unit and to a wall outlet having 120V, 60Hz only. CAUTION: Use only the AC adapter provided with the unit. Using another AC adapter may damage the unit. When not using AC power, disconnect the AC Outlet AC adapter from the wall outlet by pulling the plug (not the cord). Also used to insert a pause when programming telephone numbers into memory. The number will automatically be dialed. NOTES: Although the unit is "off-hook" when setting memories, when the PROGRAM button is pressed, the number will not actually be dialed. To insert a pause, simply press the REDIAL/PAUSE button. E12 MPH-1089-4389. O/M. QXD 5/25/01 11:35 AM Page 13 ANSWERING MACHINE OPERATION RECORDING OGM (OUTGOING MESSAGE ) Recording an OGM allows the caller to hear the OGM and then be able to leave a message. Please note that there is an automatic message on this unit, recording a new OGM will record over this default message. 1 2 2 1 Press and hold the OGM button for approximately 2 seconds until a short beep is heard ("rA" will appear in the display), and then release the button. Begin recording your outgoing message speaking in a normal tone of voice. Typical Message: "You have reached the Smith residence. We are not able to come to the phone right now. If you'll leave your name, phone number and a brief message after the beep, we will call you back. " When finished recording, press the PLAY/STOP button . A short beep will sound and the newly recorded outgoing message will then play once; "PA" will appear in the display. Make sure the SPEAKER VOLUME control is at a desirable level. [. . . ] To remotely erase all messages, press the "3" pad. playing message, press the "3" pad. REMOTE ROOM MONITORING This feature will allow you to call in and monitor the room in which the answering machine is located. 1 2 After the OGM is played, and the beep is heard, enter your security code within 10 seconds. Press the "0" pad and the unit will monitor the situation for 30 seconds, beep and then stop. If you want to continue monitoring, immediately press the "0" pad again for an additional 30 second room monitoring. To stop monitoring, press the "#" pad. E21 MPH-1089-4389. O/M. QXD 5/25/01 11:35 AM Page 22 REMOTE OPERATION HELP MENU 1 After the OGM is played, and the beep is heard, enter your security code within 10 seconds. Press the "5" pad for the help menu. [. . . ]