User manual MEMOREX MPH-4489

[. . . ] MPH-4489. O/M. QXD 5/25/01 11:34 AM Page 1 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. [. . . ] When not using AC power, disconnect the AC Outlet AC adapter from the wall outlet by pulling the plug (not the cord). Do not touch the AC adapter with wet hands. AC Adapter's Plug Battery Installation To protect the memory if there is a power failure, insert 4 "AA" size batteries (not included). To install the batteries, open the battery compartment with a slotted screwdriver as shown in the figure, insert the batteries following the diagram and replace battery compartment cover. + BATTERY PRECAUTIONS Follow these precautions when using batteries in this device: 1. Use only the size and type of batteries specified. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. Do not mix different types of batteries together (e. g. Alkaline and Carbon-zinc) or old batteries with fresh ones. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer's directions. ) E7 + + Replace the batteries when the Battery indicator lights in the display. + MPH-4489. O/M. QXD 5/25/01 11:34 AM Page 8 TELEPHONE OPERATION When the unit is first plugged in, the display will count up. This is useful for using the phone with the Call Waiting feature. HOLD Button To increase/decrease the handset's volume, slide the Handset HI/LO switch to the HI or LO position. 1 2 Press the HOLD button to put the caller on hold; the Hold indicator will light. You can then hang up the handset if desired. To take the caller off hold, pick up the handset. RECEIVING A CALL 1 To answer the call, press the SPEAKERPHONE button, or pick up the handset. E10 MPH-4489. O/M. QXD 5/25/01 11:35 AM Page 11 TELEPHONE OPERATION Manually Storing/Accessing Numbers in One-Touch Memories (M1-M3) This telephone is equipped with 3 memories for programming your most frequently dialed telephone numbers. You can store up to 16 digits in each memory position. 1 3 1 Lift the handset, or press the SPEAKERPHONE button . Press the PROGRAM button , then press the key buttons (09) to enter the desired telephone number to memorize. 2 2 Press the desired memory location (M1, M2 or M3). 3 3 1 Repeat steps 1 and 2 for additional memories. 4 2 1 2 To access M1M3 memories: When is phone is off the base or after pressing the SPEAKERPHONE button , press M1, M2 or M3 . The number will automatically be dialed. NOTES: Although the unit is "off-hook" when setting memories, when the PROGRAM button is pressed, the number will not actually be dialed. To insert a pause, simply press the REDIAL/PAUSE button. E11 MPH-4489. O/M. QXD 5/25/01 11:35 AM Page 12 TELEPHONE OPERATION Manually Storing/Accessing Numbers in Two-Touch Memories (0-9) This telephone is equipped with 10 additional memories for programming your most frequently dialed telephone numbers. You can store up to 16 digits in each memory position. 1 3 1 Lift the handset, or press the SPEAKERPHONE button . Press the PROGRAM button , then press the key buttons (09) to enter the desired telephone number to memorize. 2 2 2 1 Press the SPEED DIAL button , followed by the desired memory location (0-9) . 3 3 1 Repeat steps 1 and 2 for additional memories. 4 2 1 3 2 To access 0-9 memories: When is phone is off the base or after pressing the SPEAKERPHONE button , press the SPEED DIAL button followed by the desired memory (0-9) . [. . . ] Press the "#" pad to stop help menu. END CALL: Press the "#" pad to stop remote operation and end the call. Care and Maintenance 1. Clean your phone with a damp (never wet) cloth. Solvent or detergent should never be used. Avoid operating your unit under direct sunlight or in hot, humid or dusty places. [. . . ]