User manual MEMOREX MPH-6995-04

[. . . ] Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. [. . . ] Plug the free end of the short line cord into Wall Mount the modular wall jack. Insert the Ni-Cd battery pack into the battery compartment. 3 Put the battery cover back on by sliding it upward until it clicks into place. CHARGING THE RECHARGEABLE BATTERY Be sure the rechargeable battery is fully charged 12 hours prior to initial use. The handset's rechargeable battery will be charged when it's on the base's charge contacts; the CHARGE indicator will light when it is placed in the base. NOTES: · The Low battery indicator will appear in the display when the battery power is low and needs recharging. If the battery becomes weak while you are on a call, the Battery Low indicator in the LCD display will blink and a beep will be heard every 12 seconds. In this case, end the call immediately and return to the base for recharging. · Every few months, or when charging becomes abnormal, clean the contacts of the handset and the base with a standard pencil eraser. · To maximize battery life, fully discharge the battery every month or two. To do this, simply unplug the telephone line cord and press the TALK button until the battery is discharged, and then recharge it. 9 MPH2410. O/M. QXD 3/7/03 9:35 AM Page 10 SET-UP INSTRUCTIONS SETTING THE RINGER VOLUME Set the ringer volume (HI, LOW, OFF) while in the Standby mode as follows: 1 2 Press and hold the VOICE MAIL/ MENU button for more than two seconds; the Ringer Volume setting will appear in the display. Press the EDIT/FLASH button to change the setting; the Ringer Volume setting will blink. 3 1 4 2 Press the Scroll Up or Down button to select a desired ringer volume (HI, LOW or OFF). When the desired Ringer Volume setting appears, press and hold the SAVE/RE/PA button for more than two seconds; a long beep will be heard to confirm the setting has been saved. NOTE: A button must be pressed within 20 seconds, or the unit will revert back to the Standby mode. 5 You can continue with programming or press the VOICE MAIL/MENU button to return to the Standby mode. 10 MPH2410. O/M. QXD 3/7/03 9:35 AM Page 11 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE LANGUAGE Set the language (ENGLISH, SPANISH, FRENCH) while in the Standby mode as follows: 1 2 1 2 Press and hold the VOICE MAIL/ MENU button for more than two seconds; the Ringer Volume setting will appear in the display. Press the Scroll Down button once or the 2 key button once; the Language setting will appear. 3 4 1 2 Press the EDIT/FLASH button to change the setting; the Language setting will blink. Press the Scroll Up or Down button to select the desired language (ENGLISH, SPANISH or FRENCH). 5 6 When the desired Language setting appears, press and hold the SAVE/ RE/PA button for more than two seconds; a long beep will be heard to confirm the setting has been saved. You can continue with programming or press the VOICE MAIL/MENU button to return to the Standby mode. 11 MPH2410. O/M. QXD 3/7/03 9:35 AM Page 12 SET-UP INSTRUCTIONS (CONTINUED) SETTING THE FIRST RING This feature will turn the first ring of the phone On or Off. Set to Off so the phone does not ring until the Caller ID information has been displayed. NOTES: · If you subscribe to Caller ID, the time and date are automatically set when the first call is received. · Calls picked up on the first ring will not be logged in the Caller ID log. · Press the Scroll Right button to view caller ID information of more than 11 characters. WHAT APPEARS IN THE CALLER ID DISPLAY · · · · · · · When the incoming call has been assigned to your telephone number, the display will show "C-F" (Forwarded Call). When the incoming call is a long distance call and this service is provided by your local phone company, the display will show "L-D-C" (Long Distance Call). If a call is received from an area which does not provide caller ID service, the display will show "UNAVAILABLE". If a call was received incorrectly or only part of the data was received, the display will show "DATA ERROR". If a call is received from a caller that has blocked his/her information, the display will show "PRIVATE". Call Waiting calls are shown in the Caller ID log if you subscribe to the extra feature from the phone company that allows this. If there are new calls, the total number and "NEW CALL" will appear in the display. 22 MPH2410. O/M. QXD 3/7/03 9:35 AM Page 23 TELEPHONE OPERATION (CONTINUED) REDIALING A NUMBER CHANNEL SELECTION 1 1 1 2 Press the TALK button (the display will light), followed by the SAVE/RE/ PA button to automatically redial the last number dialed on this handset (up to 32 digits). NOTE: Please note that only the last number you called on this handset can be stored in the Redial memory. The base unit will automatically search for the clearest channel in the Talking mode. However, should you hear static or noise during the course of a conversation which makes it difficult to hear the caller, the DEL/CHAN button on the handset allows you to choose between 50 preset frequencies. ENDING A CALL ADJUSTING EARPHONE VOLUME 1 1 To end a call, simply return the handset to the base, or press the TALK button on the handset. To adjust the volume in the handset receiver, slide the Receiver Volume switch to the HI, MID or LOW position. OUT OF RANGE The handset and base communicate up to a maximum range. [. . . ] Refer to the "BLOCKED CALLS" section of the manual. No power on the handset unit Check for the Ni-Cd battery pack connection inside the battery compartment on the handset. The handset rechargeable Ni-Cd battery pack may need charging. Does not charge Make sure the charging contacts on both the base unit and the handset are in contact during charging. [. . . ]