User manual MEMOREX MVDR2102AOM

[. . . ] LOCATION OF CONTROLS QUICK SET UP GUIDE ON/STANDBY Button DV IN Jack, S-Video IN Jack and A/V IN Jacks (under door) 3. RF IN Jack Rear Video IN Right Audio IN (Rear Video/S-Video) Component Y Output Component Cb/Pb Output Video OUT Right Audio OUT AC Power Cord Optical Digital Audio Output Coaxial Digital Audio OUT Left Audio OUT S-Video OUT Component Cr/Pr Output Left Audio IN (Rear Video & S-Video) S-Video IN RF OUT Jack 1. 2. How do I stop the picture from rolling/flickering: This could be caused by the accidental pressing of the I/P (Interlace/ Progressive) button. If using a TV that is not compatible with progressive scan, press this button to select Interlace. [. . . ] 31 MTS SETTING INITIAL SETUP MENU (CONTINUED) Some TV programs broadcast additional audio. In most cases this means an additional language is available. For example, if a program is available in English and Spanish, Spanish can be broadcast as the additional audio program. To record TV programs in stereo, SAP or Dual, you can select Stereo, SAP or Dual as the default setting. 1 1 2 NOTES: · The MTS setting does not become active until the sound of a TV program is transmitted in Stereo or SAP. · When you playback the recording, you can playback the sound only in the setting you selected for recording (i. e. , a recording in SAP can be played back only in SAP). · To return to the previous row of options, press the Navigation () button. · To exit setup, press the SETUP button. Enter the TV Setup page as described on the previous page. Then, select MTS SETTING using the Navigation (, ) buttons 1, then the Navigation (®) button 1 to select it. Select the desired setting using the Navigation (, ) buttons 1, then press the ENTER button 2. SAP (Secondary Audio Program): record TV program in SAP. (Please see additional information in NOTES at the right. ) 32 1 TUNER OPERATION 2 Press the STANDBY ON/OFF button to turn on the unit. After a few seconds, the Source mode (TV Tuner, Front AV, Front SV, etc. ) screen will appear. Press the SOURCE button to select TV, "Input Tuner" and a channel number will appear on the TV. If there is no signal for the channel, "No signal" will appear on the screen. 3 4 1 2 1 2 For proper operation, before selecting channels, they must be set into the TV's program memory, see page 30. Press and release the CHANNEL Up 1 or Down 2 button. The TV automatically stops at the next channel set into memory. Direct Program Selection buttons (0- 9) Use these buttons to select a channel. The channel number will appear at the top right corner of the screen. For ANTENNA, enter a two digit channel number; i. e. , enter "02" for Channel 2, enter "69" for Channel 69, etc. For CATV, enter a three digit channel number; i. e. , enter "002" for Channel 2, enter "125" for Channel 125, etc. NOTE: · When ANTENNA/CATV option is set to ANTENNA, only channels from 02 to 69 can be selected. When set to CATV, channels up to 125 can be selected. FAQs: Why do I only receive up to channel 69, when my cable goes much higher?TV SIGNAL menu option must be set to CATV when using cable, see page 30. You must subscribe to these channels through your cable company. 33 IMPORTANT: When " " appears while pressing a button, this means that the corresponding function cannot be performed either on the disc inserted, or in the selected mode. AUDIO MODE You can cycle between the audio modes as follows: DVD BASIC OPERATION (GENERAL) 1 For DVD, Press the MTS AUDIO button repeatedly to cycle through the audio languages available on the playing DVD. Separate languages must be recorded on the DVD to use this feature. [. . . ] If the audio or subtitle language does not appear on the disc, then the initial setting will not be seen/heard. Subtitles appear only when the discs contain them. Angles may not be recorded on the disc (see disc jacket/case), or they may only be recorded on certain scenes. VCD (VIDEO CD) No menu playback. DVD RECORDER Will not record. The VCD inserted does not have the playback control. [. . . ]