User manual MERCURY PVM266AM-P

[. . . ] This publication, including photographs, illustrations and software, is under the protection of international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] The other options on the main menu page lead to dialog boxes requiring your answer Yes or No by hitting the Y or N keys. If you have already changed the setup utility, press F10 to save those changes and exit the utility. Press F5 to reset the changes to the original values. Press F6 to install the setup utility with a set of default values. Press F7 to install the setup utility with a set of high-performance values. 19 Standard CMOS Setup Page This page helps you set up basic information such as the date and time, the IDE devices, and the diskette drives. AMIBIOS SETUP ­ STANDARD CMOS SETUP (C) 2000 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yy) : Mon Apr 28, 2003 Time (hh/mm/ss) : 17:09:30 LBA Blk PIO Type Size Cyln Head WPcom Sec Mode Mode Mode Pri Master : Auto Pri Slave : Auto Sec Master : Auto Sec Slave : Auto Floppy Drive A : 1. 44 MB 31/2 Floppy Drive B : Not Installed Month : Jan ­ Dec Day : 01 ­ 31 Year : 1901 ­ 2099 32Bit Mode On On On On ESC : Exit : Select Item PU/PD/+/- : Modify (Shift)F2 : Color F3 : Detect All HDD Date & Time IDE Pri Master Pri Slave Sec Master Sec Slave Floppy Drive A Floppy Drive B Use these items to set up system date and time Use these items to configure devices connected to the Primary and Secondary IDE channels. To configure an IDE hard disk drive, choose Auto. If the Auto setting fails to find a hard disk drive, set it to User, and then fill in the hard disk characteristics (Size, Cyls, etc. ) manually. If you have a CD-ROM drive, select the setting CDROM. If you have an ATAPI device with removable media (e. g. a ZIP drive or an LS-120), select Floptical. Use these items to set up size and capacity of the floppy diskette drive(s) installed in the system. 20 Advanced Setup Page This page sets up more advanced information about your system. Any changes can affect the operation of your computer. AMIBIOS SETUP ­ ADVANCED SETUP (C) 2000 American Megatrends, Inc. All Rights Reserved Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Devices S. M. A. R. T. for Hard Disks BootUp Num-Lock Floppy Drive Swap Floppy Drive Seek Password Check Boot To OS/2 L2 Cache System BIOS Cacheable DRAM Timing by SPD DRAM Frequency DRAM CAS# Latency DRAM Bank Interleave AGP Mode AGP Comp. Driving Enabled IDE-0 Floppy CDROM Yes Disabled On Disabled Disabled Setup No Enabled Enabled Disables 100MHz 2. 5 Disabled 4X Auto CB AGP Aperture Size Auto detect DIMM/PCI Clk CLK Gen Spread Spectrum Hyper-Threading Function 64MB Enabled Disabled Disabled ESC F1 F5 F6 F7 : Quit : Select Item : Help PU/PD/+/- : Modify : Old Values (Shift)F2 : Color : Load BIOS Defaults : Load Setup Defaults Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Device If you enable this item, the system starts up more quickly be elimination some of the power on test routines. Use these items to determine the device order the computer uses to look for an operating system to load at start-up time. If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first two locations. 21 S. M. A. R. T. for Hard Disks BootUp NumLock Floppy Drive Swap Floppy Drive Seek Password Check Boot to OS/2 > 64MB L2 Cache System BIOS Cacheable DRAM Timing By SPD DRAM Frequency Enable this item if any IDE hard disks support the S. M. A. R. T. (SelfMonitoring, Analysis and Reporting Technology) feature. This item determines if the Num Lock key is active or inactive at system startup time. If you have two diskette drives installed and you enable this item, drive A becomes drive B and drive B becomes drive A. [. . . ] Please see the following illustration. The Setup button runs the software auto-installing program as explained in next section. The Browse CD button is a standard Windows command that you can check the contents of the disc with the Windows 98 file browsing interface. The Exit button closes the Auto Setup window. To run the program again, reinsert the CD-ROM disc in the drive; or click the CD-ROM driver from the Windows Explorer, and click the Setup icon. [. . . ]