User manual MERIDIAN AUDIO 50624

[. . . ] Meridian 506 24-Bit CD Player u s e r g u id e Meridian 506 24-Bit CD Player User Guide Preface i Sales and service in the UK Meridian Audio Ltd Stonehill Stukeley Meadows Huntingdon PE18 6ED England Tel (01480) 52144 Fax (01480) 459934 World Wide Web http://www. meridian-audio. com Tel (404) 344 7111 Fax (404) 346 7111 Meridian America Inc 3800 Camp Creek Parkway Building 2400 Suite 122 Atlanta GA 30331 Digital Gramophone and Wireless Ltd Stonehill Stukeley Meadows Huntingdon PE18 6ED England Copyright © 1993­1999 Digital Gramophone and Wireless Ltd Part no: 506/3 This guide was produced by Human-Computer Interface Ltd, http://www. interface. co. uk Sales and service in the USA Designed and manufactured in the UK by Preface ii Contents Introduction 1 Introduces the 506 24-Bit CD Player, and provides an overview of the other products available in the Meridian 500 Series. The Meridian 500 Series . . . . . . . . . . . . . . . . . . . . . . . . 2 Specification and accessories . . . . . . . . . . . . . . . 3 Using the CD player 5 Provides step-by-step instructions on how to operate the CD player, using either the front panel or the Meridian System Remote. [. . . ] For example: q Press Repeat again. --2O Using the CD player To pause play q Press = (Pause). The disc will remain spinning and the display will show Pause. For example: 3 Pause 9 Programming a selection With the remote you can programme a selection of tracks, and then play only those tracks you have programmed. You can programme a selection either by storing the tracks you want to play, or by clearing the tracks you do not want to play. If you programme a selection by storing the tracks you want to hear, you can play the tracks in any order and repeat tracks in the sequence. You can programme a selection while the disc is playing, in which case the selection will be played after the current track finishes. You should store the track within two seconds, or it will begin to Attempting to programme more than 31 tracks will display an error warning: Using the CD player To programme by specifying the tracks you want to play q Choose the first track you want to play, as described above. The display will show the track number; for example: Track 14 The display will change to: Store 14 Error play. The track will be labelled Store. To choose a track to programme All the other tracks are initially programmed not to play, and will q Press Next or Previous to step through the track numbers until the track you want is displayed, or type the number of the track you want. be labelled Clear. 10 To programme by specifying the tracks you do not want to play q Choose one of the tracks you do not want to play, as described above. The Clear label will change to Store to indicate that the track is stored. To remove a track from a selection Select the track you want to remove, as described above. The display will show the track number; for example: q Press Clear (remote only). The display will change to: Track 12 q Press Clear (remote only). The Store label will change to Clear to indicate that the track has Clear 12 been cleared. To clear a programme You should clear the track within two seconds, or it will begin to play. All the other tracks are initially programmed to play, and will be labelled Store. q Press · (Stop) twice. Using the CD player The display will show C. P. (Cancel Programme): C. P. To add a track to a selection q Select the track you want to add, as described above. q Press Store (remote only). A programme is automatically cancelled if you open the disc drawer, or press Off. 11 Disc information and scanning To change the display q Press Display. Each time you press the appropriate key, the display will step between the following display options: Display Track (and index) number. Example During scanning, the sound is muted and the display automatically changes to show the elapsed time for the whole disc, unless you have already selected one of the other time displays. Scanning a disc The scan controls allow you to move quickly to any position on the disc at approximately 20 times normal speed. 14 This function is only available from the remote. Elapsed time for the whole disc. 58:12 0:59 1:47 14 14 14 To scan through a disc q Hold down or ¯ (remote only). You are advised to retain the packing in case you need to transport the unit. FCC Warning: This equipment generates and can radiate radio frequency energy and if not installed and used correctly in accordance with our instructions may cause interference to radio communications or radio and television reception. It has been type-tested and complies with the limits set out in Subpart J, Part 15 of FCC rules for a Class B computing device. These limits are intended to provide reasonable protection against Setting up the CD player In common with all CD players, the 506 24-Bit CD Player emits some radio-frequency signals. [. . . ] r Relocate the receiver with respect to the CD player. r Connect the receiver and this product to different AC outlets. 22 Maintenance Cleaning When cleaning the CD player bear in mind that the front of the CD player is plastic, and the display panel and lid are glass. Disconnect the power cord before cleaning the unit. Note: Do not use abrasive cleaners on any part of the CD player. [. . . ]