User manual MERIDIAN AUDIO G07 88

[. . . ] G Series CD Player Installation Guide ii Preface Important safety instructions · Read the instructions. · Do not use this apparatus near water. · Install only in accordance with the manufacturer's instructions. · Refer all servicing to approved service personnel. To avoid interference Do not position the product: · Near strong magnetic radiation, such as near a power amplifier. [. . . ] · Meridian G Series System Guide. If any of these items are missing please contact your dealer. Note: You should retain the packaging in case you need to transport the unit. 6 Installing the CD player Audio connections G07 24-bit CD Player Analogue outputs G07 24-BIT CD PLAYER ON CAUTION REPLACE WITH SAME TYPE FUSE T160mAL for 100 - 120V T80mA for 220 - 240V POWER INPUT ~50-60Hz 40VA MAX OFF DESIGNED AND MADE IN ENGLAND BY MERIDIAN AUDIO LTD DESIGN AND COPYRIGHT 2003 SERIAL NUMBER VOLTAGE TESTED ANALOGUE OUT L DIGITAL OPTICAL OUT OUT MERIDIAN COMMS MAINTENANCE RS232 IR IN WARNING SHOCK HAZARD - DO NOT OPEN NO USER SERVICEABLE PARTS INSIDE CLASS 1 LASER PRODUCT R DOUBLE INSULATED PRODUCT Digital output Optical output Use this output ANALOGUE OUT DIGITAL OUT OPTICAL OUT To connect to this The analogue inputs of a preamplifier, such as the G01 Control Unit, or an integrated amplifier, such as the G51 Receiver, using analogue phono leads. The digital input of a surround processor, such as the G68 Digital Sound Controller, or DSP loudspeakers, using a 75 digital cable. The optical input of a digital preamplifier or digital recorder, using a TOSlink optical cable. 7 Installing the CD player G08 24-bit Upsampling CD Player Unbalanced outputs G08 24-BIT UPSAMPLING CD PLAYER DESIGNED AND MADE IN ENGLAND BY MERIDIAN AUDIO LTD DESIGN AND COPYRIGHT 2003 CAUTION REPLACE WITH SAME TYPE FUSE T1. 6AL 250V for 100 - 240V POWER INPUT ~50-60Hz 40VA MAX WARNING SHOCK HAZARD DO NOT OPEN NO USER SERVICEABLE PARTS INSIDE SERIAL NUMBER WARNING SHOCK HAZARD - DO NOT OPEN NO USER SERVICEABLE PARTS INSIDE CLASS 1 LASER PRODUCT ON OFF VOLTAGE TESTED BALANCED OUT R ANALOGUE OUT L BALANCED OUT L OPTICAL OUT DIGITAL OUT IR IN MAINTENANCE RS232 MERIDIAN COMMS R Balanced outputs Optical output Digital output Use this output BALANCED OUT ANALOGUE OUT DIGITAL OUT OPTICAL OUT To connect to this The balanced analogue inputs of a preamplifier, such as the G02 Balanced Control Unit, using XLR leads. The unbalanced analogue inputs of a preamplifier, such as the G01 Control Unit, or an integrated amplifier, such as the G51 Receiver, using analogue phono leads. The digital input of a surround processor, such as the G68 Digital Surround Controller, or DSP loudspeakers, using a 75 digital cable. The optical input of a digital preamplifier or digital recorder, using a TOSlink optical cable. 8 Installing the CD player To connect to a digital surround controller (eg G68) G07/G08 G68 Digital Surround Controller COMMS DIGITAL IN DIGITAL OUT COMMS COMMS LEAD DIGITAL LEAD · Connect the DIGITAL output from the G07 or G08 to a suitable DIGITAL input on the digital surround controller, using a digital lead. · If the digital surround controller is a Meridian product connect together the COMMS sockets using the Comms lead provided. To connect the G08 to a preamplifier with balanced inputs (eg G02 Balanced Control Unit) G08 24-bit Upsampling CD Player BALANCED OUTPUTS G02 Balanced Control Unit BALANCED INPUTS COMMS COMMS COMMS LEAD XLR LEADS · Connect the BALANCED outputs from the G08 to the balanced inputs on the preamplifier, using XLR leads. A computer, for configuring the CD player. A G12 IR Receiver, or approved alternative infra-red repeater. Contact your dealer for details. 11 Installing the CD player To connect to other Meridian G Series, 500 Series, or 800 Series equipment G07/G08 G Series, 500 Series, or 800 Series unit COMMS COMMS LEAD COMMS COMMS LEAD In a system of Meridian products, one of the products acts as the controller for the system, receiving infra-red commands from the MSR+, and then, if appropriate, relaying them to the other products via the Comms link. The following procedure should be used to set up the Comms correctly between several products: · Connect one of the DIN COMMS sockets on the back panel of the CD player to one of the COMMS sockets on another G Series, 500 Series, or 800 Series unit, using the Comms leads provided with the products. One unit will then be designated as the controller, and display: Con. All the other units will be configured as non-controllers, and display: Not Con. If for any reason the automatic setup does not work, make sure you are operating the MSR+ from a position where all the units can receive the infra-red, and try again. The sequence in which you connect the units is not important. · Switch all the units to standby. Each unit will display: If this fails: · Restore the default operation by selecting one of the standard types; see Resetting the product, page 13. Auto Note: Do not, under any circumstances, connect any equipment other than Meridian G Series, 500 Series, or 800 Series to any socket marked COMMS on the back of the product. 12 Installing the CD player 13 Resetting the CD player Resetting the CD player This chapter explains how to reset the CD player using the front-panel controls. Resetting the product The CD player provides several alternative standard settings, called Types, which configure all aspects of the product into the most commonly needed configurations. · Press Reset. The display shows: Reset Player Choosing one of the Types overrides any other configuration you may have performed, and so can be used to reset the configuration of the unit. To reset the configuration · If necessary press On/Off to put the CD player into standby. Volume display off Exit Yes · Press Yes to reset the CD player settings. The display shows the current Type: · Press More. Exit Type 1 óòô öõú The display shows: · Press A or V to step through the available Types. Version Reset 14 Resetting the CD player A description of each Type is shown on the top line of the display. As you select each Type the CD player is reset to that Type. When you have selected the Type you want: · Press Exit or On/Off to return to standby. Types The following table lists the available Types: Type Type 1 Type 2 Type 3 (G08 only) Description Volume display off. Volume display off, digital output limited to 44. 1kHz. [. . . ] Do not use any other solvent or abrasive based cleaners. Dust can be removed from the disc drive tray with a small dry brush when the drawer is open. Ensure that no liquid enters the casework and that the product is completely dry before re-connection. To clean the audio connections The audio sockets on the back of the product are gold plated and do not need to be cleaned if gold-plated plugs are used. [. . . ]