User manual METO-FER KZL 12

[. . . ] OPERATING MANUAL METO-FER® AUTOMATION AG COMPACT GRIPPER TYPE KZL 12 KZL 20 KZL 25 KZL 32 KZL 50 SERIES FROM 2-16 1. 1. 1 PRODUCT DESCRIPTION Introduction 1. 1. 1. [. . . ] Performance Characteristics Type KZL 12 KZL 20 KZL 25 KZL 32 KZL 50 Clamping force at 72. 5PSI (5 Bar) 7 lb. ( 31 N) ( 88 N) ( 137 N) ( 225 N) ( 550 N) Air consumption for each double stroke at 72. 5 PSI (5 Bar) . 0002 scf (0. 004 NL) . 0005 scf (0. 014 NL) . 0010 scf (0. 027 NL) . 0025 scf (0. 072 NL) . 0079 scf (0. 224 NL) NL: Normal Liter 1. 2. 3 Operating Source 40mm filtered, unoiled or oiled air (dew point 6oC) Operating pressure Pmin 3 bar Pmax 8 bar 1. 2. 4 Connections Air connections 1. 2. 5 Environment Temperature Relative humidity Purity of the environment air 50oF to 122oF (+ 10oC to + 50oC) 95% (without condensation of water) regular working place atmosphere M5 (see sheet 6) 3 OPERATING MANUAL (KZL) 1. 3 1. 3. 1 Features Standard Features The compact gripper KZL (KZL. . . D) includes a sensor bracket for checking the end position. It is possible to add this sensor bracket later on by ordering KZL. . . Q. The inductive proximity sensors are not included. 1. 3. 2 Special Equipment The compact grippers KZL (KZL. . . D) can be equipped with proximity switches (see Meto-Fer® Electronic Catalog Page 15) so you will be able to check open and closed positions. Gripper KZL 12 D KZL 20 D KZL 25 D KZL 32 D KZL 50 D Inductive Proximity Switches IM-004-. . . -. . . 2. 1 SAFETY REGULATIONS In general See chapters 1. 1. 1 1. 1. 2 1. 1. 3 2. 2 Specifically Do not make any changes or modifications to the unit (voids warranty). 3. CONSTRUCTION AND FUNCTION To check the end position, the compact gripper can be equipped with inductive proximity switches. The stroke (clamp) cannot be adjusted. 4 OPERATING MANUAL (KZL) 4. 4. 1 INITIAL OPERATION Compressed Air Remove the safety caps from the air connections. In order to regulate the velocity of the movement, we recommend our flow controls DV-M5 (see sheet 5. 021). 5. 5. 1 MAINTENANCE Introduction The compact gripper unit does not require any special maintenance procedure Never use any type of solvents in order to clean the unit. 5. 2 Air Supply The mini linear unit is equipped with oil-free seals and can be operated with dry and non-oiled compressed air. If oiled compressed air is used, we recommend: Airpress compound SAE 5 (Klueber Order No. 6. 1 REPAIR Introduction If the unit no longer meets the requirements (leakage, wear, etc. ) the defective parts must be replaced. 6. 2 Safety Precautions Before dismounting the unit, it is necessary to check that the compressed air supply is turned off. [. . . ] 7. 1 SPARE PARTS LIST Spare Parts When ordering spare parts, the type and serial number of the unit must be supplied. Seal Kit Order Number 460. 100. 0302 Position Order Description Number 201 025. 100. 0320 O-Ring 202 025. 100. 0160 O-Ring 203 025. 150. 0500 Piston Seal Seal Kit Order Number 460. 100. 0304 Position Order Description Number 201 025. 100. 0520 O-Ring 202 025. 100. 0230 O-Ring 203 025. 150. 0550 Piston Seal Seal Kit Order Number 460. 100. 0306 Position Order Description Number 201 025. 100. 0580 O-Ring 202 025. 100. 0270 O-Ring Type Quantity 1 Piece 1 Piece 1 Piece KZL 12 Type Quantity 1 Piece 1 Piece 1 Piece KZL 20 Type Quantity 1 Piece 1 Piece KZL 25 6 203 025. 150. 0600 Piston Seal 1 Piece 7 OPERATING MANUAL (KZL) Type KZL 32 Seal Kit Order Number 460. 100. 0308 Position Order Description Number 201 025. 100. 0660 O-Ring 202 025. 100. 0310 O-Ring 203 025. 150. 0650 Piston Seal Seal Kit Order Number 460. 100. 0309 Position Order Description Number 201 025. 100. 0795 O-Ring 202 025. 100. 0420 O-Ring 204 025. 150. 0700 Piston Seal Quantity 1 Piece 1 Piece 1 Piece Type Quantity 1 Piece 1 Piece 1 Piece KZL 50 7. 2 Lubrication Grease for seals Staburag NBU 4 Atemp. [. . . ]