Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual METO-FER ML 26. We hope that this METO-FER ML 26 user guide will be useful to you.
Lastmanuals help download the user guide METO-FER ML 26.
Detailed instructions for use are in the User's Guide.
[. . . ] (Type O, A, B, C) is able to execute linear movements in any position. This linear movement can be adjusted in its working area (stroke). Safety Precautions Before starting to operate the mini linear unit ML 26-. . . [. . . ] 4. 1
INITIAL OPERATION Compressed Air Remove the safety caps from the air connections. In order to regulate the velocity of the movement, we recommend our flow controls DV-R1/8" (see sheet 5. 021). Unused air connections must be covered with the R1/8 caps.
4. 2
Stroke Adjustment loosen security nut on the end screw adjust the required stroke with the end screw (Pos. 101) tighten security nut on the end screw
4. 3
Cushion Adjustment The basic adjustment of the cushions has to be optimized by the user upon his special requirements. The position of the cushions can be seen on the construction drawing. The brake resistance can be changed by adjusting the length of the brake path. When using oil and elastomer cushions, it must be checked that the end stop is not made by the cushions. The cushions should show a remainder stroke of 0. 0394" (1mm).
5. 5. 1
MAINTENANCE Introduction The mini linear unit does not require any special maintenance procedure Never any type of solvents in order to clean the unit. Air Supply The mini linear unit is equipped with oil-free seals and can be operated with dry and non-oiled compressed air. If oiled compressed air is used, we recommend: Airpress compound SAE 5 (Klueber Order No. 063027)
use 5. 2
5
6
OPERATING MANUAL (ML 26)
6. 6. 1
REPAIR Introduction If the unit no longer meets the requirements (leakage, wear, etc. ) the defective parts must be replaced.
6. 2
Safety Precautions Before dismounting the unit, it is necessary to check that the compressed air supply is turned off. It is best to disconnect the compressed air supply from the unit. When repair work is done, only the original spare parts and lubrication must be used.
6. 3
Replacing the Seals Remove the end plate (Pos. 2) by loosening the set screw (Pos. 202). [. . . ] 7. 1 SPARE PARTS LIST Spare Parts
When ordering spare parts, the type and serial number of the unit must be supplied. Position *206 *207 208 *214 Seal Kit Repair Kit 7. 2 Lubrication Grease for seals Grease for linear ball bushings Staburag NBU 4 Atemp. 005 040) Part Number 025. 150. 0800 025. 140. 0057 045. 100. 0006 025. 100. 0585 Description Piston Seal Rod Seal Linear ball bushings O-Ring Quantity 1 piece 1 piece 4 pieces 1 piece
Order No. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE METO-FER ML 26
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual METO-FER ML 26 will begin.
