User manual METO-FER VE-22-A

[. . . ] OPERATING MANUAL ® METO-FER AUTOMATION AG VERTICAL UNIT TYPE VE-22-A VE-52-A VE-82-A VE-82-B 1. 1. 1 PRODUCT DESCRIPTION Introduction 1. 1. 1. Utilization The vertical unit VE 22/52/82 (Type A, B) is able to execute linear movements in any position. [. . . ] Vertical Unit Conical Bar for Mechanical Conical Bar Length Gripper MZ 12 VE-22 KS-01-061 6. 02"/153mm VE-52 KS-02-062 8. 38"/213mm VE-82 KS-01-063 10. 74"/273mm Vertical Unit Conical Bar for Mechanical Gripper MZ 25 KS-02-070 KS-02-071 KS-02-072 Cone VE-22 VE-52 VE-82 2. 2. 1 KS-02-005 KS-02-005 KS-02-005 Total Length Conical Bar/Cone 10. 15"/258mm 12. 51"/318mm 14. 88"/378mm SAFETY REGULATIONS In general See chapters 1. 1. 1 1. 1. 2 1. 1. 3 3 OPERATING MANUAL (VE) 2. 2 Specifically Under no circumstances are any changes or modifications to be made on the unit. 3. CONSTRUCTION AND FUNCTION The stroke adjustment can be made infinitely variable with the end screw AS 08/40 (Pos. 101) in order to check the occurred movement, the end screws can be fitted with our sensing elements (see Meto-Fer® Electronics catalog). 4. 4. 1 INITIAL OPERATION Compressed Air Remove the safety caps from the air connections. In order to regulate the velocity of the movement, we recommend our flow controls DV-M5 (see sheet 5. 021). Unused air connections must be covered with the M5 caps. 4. 2 Stroke Adjustment loosen security nut on the end screw adjust the required stroke with the end screw (Pos. 101) tighten security nut on the end screw 4. 3 Cushion Adjustment The basic adjustment of the cushions has to be optimized by the user upon his special requirements. The position of the cushions can be seen on the construction drawing. The brake resistance can be changed by adjusting the length of the brake path. When using oil and elastomer cushions, it must be checked that the end stop is not made by the cushions. The cushions should show a remainder stroke of 0. 039" (1mm). 4 OPERATING MANUAL (VE) 5. 5. 1 MAINTENANCE Introduction The mini linear unit does not require any special maintenance procedure. Never use any type of solvents in order to clean the unit. 5. 2 Air Supply The mini linear unit is equipped with oil-free seals and can be operated with dry and non-oiled compressed air. If oiled compressed air is used, we recommend: Airpress compound SAE 5 (Klueber Order No. 6. 1 REPAIR Introduction If the unit no longer meets the desired requirements (leakage, wear, etc. ) the defective parts must be replaced. 6. 2 Safety Precautions Before dismounting the unit, it is necessary to check that the compressed air supply is turned off. It is best to disconnect the compressed air supply from the unit. When repair work is done, only the original spare parts and lubrication must be used. 6. 3 Replacing the Seals Remove the top end plate (Pos. 2) by loosening screws (Pos. 216 and 202). Remove the bottom end plate (Pos. 3) by loosening screws (Pos. 202) and extract by help of press. [. . . ] Position *205 *206 *207 *208 209 211 Seal Kit Repair Kit 7. 2 Lubrication Part Number 025. 100. 0530 025. 230. 0040 025. 140. 0058 025. 150. 0600 045. 110. 0030 045. 100. 0075 Description O-Rings Seal Rings Rod Seals Piston Seal Bearing Linear Ball Bushings Amount 2 pieces 2 pieces 2 pieces 1 piece 1 piece 2 pieces Order No. 460. 100. 0199 all items marked with (*) Order No. 460. 110. 0028 kit includes Pos. 209 and 211). 6 Grease for seals Grease for linear ball bushings Staburag NBU 4 Atemp. [. . . ]