User manual METRONIC 427013 QUICK GUIDE

[. . . ] If it is not the case, try to reach as precisely as possible the desired angle with a continuing rotation. It is useful to keep the degree order precision. 0 208 994 11 81 2 6 - Give a number to a satellite Check in your receiver user manual how to associate a number to each satellite. If it is not possible, leave the existing number system. 7 - Memorise a satellite position This function is generally called memorised, store, saved. . . 8 - Display the signal indicator Generally, the signal indicator appears when pressing on the INFO key. Sometimes, you have to access the channel search menu. [. . . ] When the right angle as been adjusted, tighten the screw, and the nut 2d as well. 0 208 994 11 81 8 Inclination and angular reading for Hotbird 3 9 0 208 994 11 81 D Connection For the installation you will need 2 pieces of cable. The first one, roughly 1, 5m (4, 92ft) to go from the LNB to the motor, the second one as long as it takes to go from the motor to the receiver. Prepare the cables and assemble the "F" plug at the end of the cable. Respect the dimension indicated on the diagram below; the plug must screw on the aluminium foil roll up. Make sure that none of the braid strand is in contact with the central core of the cable. Connect the receiver to the television set with a scart lead. Put the motor near the receiver, on a table or on the floor, and connect the receiver LNB input to the Motor DEMO output with the 1, 5m (4, 92ft) cable, then switch on the receiver. Moteur Horizon-Horizon Réf. 450908 S/N 3mm441550nnnnnn 0 208 994 11 81 10 E Reset the motor and checking of the stop The reset of the motor is to reinitialise its position, and not to put him at 0°, which means face south. Go into the DiSEqC 1. 2 (2) menu and then reset the motor (3). · The motor will reinitialise while looking for his reference position (Mechanic east stop). The motor should stop at 45° (At the nearest 10°). · Put the receiver on the Hotbird reference channel. 0 208 994 11 81 14 Go to corresponding paragraph page 2 and 3 (4) H1 North 12 South 15 0 208 994 11 81 I Assembling the LNB head Check the LNB and receiver user manual. WARNING, some LNB need to be assembling at 45°! J Checking Before going to the final stage (the alignment) check that your installation looks like the picture below. 11 0 208 994 11 81 16 K Alignment / Satellite dish orientation · At the end of the step K, you will receive the Hotbird reference channel on the television screen. Do not go to step L (adjusting the alignment) if you do not receive it. 1) Put the receiver on the Hotbird reference channel then display the signal indicator (8). 2) Launch a slow scan (for 20 seconds) a quarter of the way on the right, then a quarter of the way on the left while pivoting the whole (satellite dish + rotor) around the mast, while checking the level. If the level is not going up, increase the satellite dish incline of 2° and do the same manual scan. Carry on as above by step of 2° followed by a scan until the level increase. When you are on the right satellite, the image will appear in the background. Adjust it to obtain the maximum in level and quality (bar the longest as possible). In some area, it is normal that you will turn up to 20 scanning, be patient. Warning: the Tighten of the nut is enough to debase the picture. [. . . ] · Go into the DiSEqC 1. 2 (2) menu and give a number (6) to Astra 19°E (03 if you hesitate). · By a continuing rotation (4) and then a step by step rotation (5), make the motor spin to obtain the maximum level and quality. · Memorised (7) the founded position. · Check that you receive the Astra channel. [. . . ]