User manual MICROTEK GNC I SMI800 0805

[. . . ] Scan Type ­ Selects the output image type (color, gray, or B&W). See "Using the TMA" (back section) for more details. Purpose ­ Sets the image resolution to match your target application. NOTE: Click the Scale Output, Adjust, and Reset buttons if you need to make further adjustments. NOTE: To lock the scanner (for shipping and other reasons), refer to the ScanMaker i800 Supplement. Black Mat Hi-Speed USB cable FireWire cable EZ-LockTM Film Holders For details on how to use the Advanced Control Panel, refer to the ScanMaker i800 Supplement. Connect Scanner Power adapter Power cord Software CDs To the scanner lid Make sure the scanner lid (TMA) is properly installed, with its connector securely connected to the scanner's 15-pin accessory port. Install Software Important: Do not remove the yellow stickers from your scanner until you are told to do so. You must install software before connecting your scanner. [. . . ] Restart your computer. NOTE: After rebooting your Macintosh, the Microtek software will attempt to locate your scanner on the system. Since this is your first install and you have not yet connected the scanner, simply ignore the message that appears and proceed to the next step. · · · · · D. Connect one end of the Hi-Speed USB cable to your computer. Connect the other end of the Hi-Speed cable to the scanner's USB port. Press the power button at the front panel of your scanner, and wait for the LEDs to stop blinking and stay on steady. The system will detect your scanner automatically. Power button F DIGITAL ICE Scan Copy E-mail OCR PDF Custom NOTE: If your computer has both Hi-Speed USB (USB 2. 0) and USB 1. 1 ports, connect the cable to the Hi-Speed USB port. Use the USB 1. 1 port only if your computer does not have Hi-Speed USB. Also, refer to the ScanMaker i800 Supplement for details on how to connect the scanner using the FireWire port. TURN OVER TO CONTINUE Using the TMA A. Load the film inside the EZ-LockTM Film Holder, with the film's shiny base facing down. Using DIGITAL ICE and ColoRescue 4. Click the Scan Material button in the ScanWizard Preview window. Choose "Negative" or "Negative Film" to scan negative film, or choose "Positive" or "Positive Film" to scan transparencies and slides. Do You Need Assistance? Manuals If you have additional questions and need further instruction or information, we provide PDF manuals for: 1. Using the ScanWizard 5 scanning software EZ-Lock 35mm Slide Holder 2. Using the bundled third-party software To access the PDF manuals: Insert the scanner's software CD-ROM into your computer's CD-ROM drive. Next, locate and click the "Manuals" option when the software installer window appears on your screen. Finally, select and click the title of the manual you wish to view. Mac OS X Windows XP 5. In the ScanWizard Settings window, verify the DIGITAL ICE strength setting. "Normal" is sufficient in most cases. EZ-Lock 35mm Filmstrip Holder Missing Items If your package is missing items, please call the number below. Customer Service Department 310-687-5940 Reconstructing Damaged Photos and Film EZ-Lock 6 x 22 cm Film Holder Visit www. support. microtek. com/gold/ for Customer Service hours. The DIGITAL ICE feature repairs cracks, tears, and rips in your damaged photos and film. Raise the scanner lid, and place the photo on the scan bed. Make sure the Black Mat is attached to the scanner lid, so that uneven photos lay as flat as possible. Press the DIGITAL ICE button on the front panel of the scanner. DIGITAL ICE will automatically repair the damaged photo, and the reconstructed file is saved in the default image folder. NOTE: You can also use DIGITAL ICE to repair photos through ScanWizard 5. [. . . ] Off Scanner is off. 6) Exact wording of any error message that may have appeared on the screen 7) What happened and what you were doing when the problem occurred Note: Advanced troubleshooting is available for a consulting fee. For a detailed listing of yourTechnical Support options, go to: www. support. microtek. com/gold/ Third-Party Software Assistance For technical support or any questions you have on third-party software which may be included with your package, please use the manufacturer websites listed below. Manufacturer ABBYY® Software House Adobe® Systems, Inc. Ulead® Website www. abbyyusa. com www. adobe. com www. lasersoft. com www. lizardtech. com www. scansoft. com www. simplestar. com www. ulead. com B. Remove the Black Mat: Raise the scanner lid, and push the Black Mat to the side to remove it from the scanner lid. First, make sure that you have followed installation steps 1 through 4. [. . . ]