User manual MICROTEK GNC M CX6 0904

[. . . ] User's Manual CX6 DLP Projector www. microtek. com Conference Projectors Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright September, 2004 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no repr esentations or warranties with respect to the contents hereof and specifically disclaims any im plied warranties of merchantability or fitness for any particular purpose. [. . . ] (Range: 0-- 100) to adjust the video tint/hue. (Range: 0 -- 100) to adjust the gamma correction of the display. Input PC MAC Video Chart B&W Gamma 2. 2 1. 8 2. 4 2. 2 2. 4 Brightness High High Low Low High PC Color Space Press to adjust the color space. (Range: Auto -- RGB -- YPbPr --YCbCr) Resets all Main items settings except Color Saturation to default values Auto - Reset ­ 19 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu Main Menu Items Supported for Each Input Source Depending on the video source not all items in the OSD are available. Items that are available for each input source are marked with "X". Items that are not available can not be selected in the OSD. Function Brightness Contrast Sharpness Color Temperature Color Saturation Color Tint Gamma X X RGB X X X X DVI X X X X Component Video X X X X X X X Composite V ideo X X X X X X X S-Video X X X X X X X ­ 20 ­ On--Screen Diispl ay Men u Settti n gs O cr p ay Men en Setup Menu Press the Menu button to open the OSD menu. Press to move up and down in the Setup menu. Press to change values for settings, and then press Enter to confirm the new setting. ITEM Horizontal Position Vertical Position Press DESCRIPTION to move the image left or right. (Range: 0 --100) DEFAULT 50 Press to move the image up or down. (Range: 0 --100) 50 ­ 21 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu ITEM Keystone DESCRIPTION Press to correct distortion of the projected image. (Range: -50 --50) Press to toggle between the 4:3 standard format and 16:9 High Definition TV (HDTV) format. DEFAULT 0 Aspect Ratio Advance Feature Reset 4:3 Resets Keystone and Aspect Ratio to default values Setup Menu Items Supported for Each Input Source Depending on the video source not all items in the OSD are available. Items that are available for each input source are marked with "X". Items that are not available can not be selected in the OSD. Function Horizontal Position Vertical Position Keystone RGB X X X X X X X DVI Component Video Composite V ideo S-Video ­ 22 ­ On--Screen Diispl ay Men u Settti n gs O cr p ay Men en Config Menu Press the Menu button to open the OSD menu. Press to move up and down in the Config menu. Press to change values for settings, and then pr ess Enter to confirm the new setting. ITEM Blank Screen Auto Source Auto Power Off Volume Menu Position Menu Display Translucent Menu Reset DESCRIPTION Press to select a background color for blank screen (Range: Black ­ Red-- Green -- Blue --White) Press to enable or disable automatic source detection (Range: On -- Off) Press to enable or disable automatic shut-down of lamp after 10 mi n utes of inactivity (Range: On --Off) Press to adjust the audio volume level (Range: 0 - 10) DEFAULT Blue On Off 5 Center 15 Off Press to position the OSD on screen (Range: Left --Right --Center -- Down --Up) Press to determine the timeout delay of the OSD (Range: 10 - 20 sec. ) Press to set menu screen translucency (Range: On -- Off) Resets all Config screen items to default values ­ 23 ­ D LP Projje c tor -- U se r Manu al D Pr e c r se r Manu Utility Menu Press the Menu button to open the OSD menu. Press to move up and down in the Utility menu. Press to change values for settings, and then press Enter to confirm the new setting. ITEM Video Type Video AGC D ESCRIPTION Press to select the video standard. (Range: Auto --NTSC --PAL -- SECAM) Press to enable or disable aut omatic gain control for the video source. (Range: On -- Off) Press to choose from four projection methods: Desktop mount, front of screen D EFAULT Auto On Projection Desktop front Desktop mount, rear of screen Ceiling mount, front of screen Ceiling mount, rear of screen Frequency Press to adjust the A/D sampling clock. (Range: 0 --180) Press to adjust the A/D sampling number. [. . . ] Turn off other Infrared-enabled devices in the vicinity. Have the remote control serviced. Audio Problems Problem: There is no sound 1. Test the source audio output with other speakers. Have the projector serviced. Problem: The sound is distorted 1. [. . . ]