User manual MICROTEK MS4

[. . . ] User's Manual MS4 DLP Projector www. microtek. com Conference Projectors Copyright This publication, including all photographs, illustrations and software, is protected under international copy right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright July , 2004 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no repr esentations or warranties with respect to the contents hereof and specifically disclaims any implie d warranties of merchantability or fitness for any particular purpose. [. . . ] (Range: 0-- 100) button to adjust the contrast. (Range: 0 -- 100) button to adjust the display sharpness (Range: 1-5) DEFAULT 50 50 3 Normal Press the cursor button to adjust the video tint/hue. (Range: Cool/Normal/Warm) Press the cursor Press the cursor Press the cursor Input PC MAC Video Chart B&W button to adjust the video saturation. (Range: 0-- 100) button to adjust the video tint/hue. (Range: 0--100) button to adjust the gamma correction of the display. Gamma 2. 2 1. 8 2. 4 2. 2 2. 4 Brightness High High Low Low High 50 50 PC Color Space Reset Press the cursor button to adjust the color space. (Range: Auto ­ RGB ­ YPbPr - YCbCr ) Resets all Quality items settings to default values Auto - Setup Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Setup menu. Press the cursor button to move up and down in the Setup menu. ITEM Horizontal Position Vertical P osition Keystone Press the cursor DESCRIPTION button to move the image left or right. (Range: 0-- 100) DEFAULT 50 Press the cursor button to move the image up or down. (Range: 0-- 100) 50 Press the cursor button to correct distortion of the projected image. (Range: -20 -- +20) Press the cursor button to toggle betwee n the 4:3 standard format and 16:. 9 High Definition TV (HDTV) format. Resets Keystone and Aspect Ratio to default values 0 4:3 Aspect Ratio Reset Config Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Config menu. Press the cursor button to move up and down in the Config menu. ITEM Blank Screen Auto Source Auto Power Off Volume Menu Position Menu Display Translucent Menu Reset DESCRIPTION Press the cursor button to select a background color for blank screen (Range: Black ­ Red ­ Green ­ Blue ­ White) Press the cursor (Range: On ­ Off) button to enable or disable automatic source detection DEFAULT Blue On On 4 Center 15 Off Press the cursor button to enable or disable automatic shut- down of lamp after 10 min. of inactivity (Range: On ­ Off) Press the cursor button to adjust the audio volume level (Range: 0 - 8) Press the cursor button to position the OSD on screen (Range: Left ­ Right ­ Center ­ Down ­ Up) Press the cursor button to determine timeout delay of OSD (Range: 10 - 20 sec. ) Press the cursor button to set menu screen translucency (Range: On ­ Off) Resets all Options screen items to default values Utility Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Utility menu. Press the cursor button to move up and down in the Utility menu. ITEM Video Type Video AGC D ESCRIPTION Press the cursor button to select the Video standard (Range: Auto ­ NTSC ­ PAL ­ SECAM) Press the cursor button to enable or disable aut omatic gain control for video source. (Range: On ­ Off) Press the cursor tion methods: button to choose from four projec- D EFAULT Auto On Projection Desktop front Desktop mount, front of screen Desktop mount, rear of screen Ceiling mount, front of screen Ceiling mount, rear of screen Frequency Tracking Press the cursor button to adjust the A/D sampling clock. (Range: 0° - 180°) Press the cursor button to adjust the A/D sampling number. (Range: 1 - 100) Resets Video Type, Video AGC, and Projection to default values Auto detected Auto detected Reset Language Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Language menu. [. . . ] Direct the remote control towards remote sensor on the projector. Ensure the path between remote and sensor is not obstructed. Turn off any fluorescent lights in the room. Turn off other Infrared-enabled devices in the vicinity. [. . . ]