User manual MIELE DA279-4-VENTILATION SYSTEM

[. . . ] Operating and Installation Instructions Ventilation System DA 279-4 To prevent accidents and machine damage, read these instructions before installation or use. UV M. -Nr. 06 713 420 Contents IMPORTANT SAFETY INSTRUCTIONS Functional description Guide to the appliance Operation Turning on the fan . 15 Cleaning and Care Cleaning the casing . 20 After Sales Service Installation instructions Caring for the environment Installation accessories Plywood backing Electrical data Appliance dimensions Installation Installation instructions . [. . . ] The lit indicator shows the programmed time: 1st indicator from the left 2nd indicator from the left 3rd indicator from the left 4th indicator from the left = = = = 20 hours 30 hours 40 hours 50 hours ^ Use the "­/+" button to select the desired time. ^ Store the selection by pressing the grease filter button. ^ Press the On/Off button to turn off the fan. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. ^ Press the Delayed Shut Down and grease filter buttons at the same time. 15 Operation Reprogramming the charcoal filter timer The active charcoal filter can only be used in recirculation mode and cannot be used to exhaust fumes. The charcoal filter timer is not preset. Before using the hood in recirculation mode, the charcoal filter timer must be programmed. The indicator for the charcoal filter and one of the "­/+" indicators will flash. The lit indicator shows the programmed time: 1st indicator from the left = 120 hours 2nd indicator from the left = 180 hours 3rd indicator from the left = 240 hours 4th indicator from the left = deactivated ^ Use the "­/+" button to select the desired time. ^ Turn off the fan using the On/Off button. ^ Press the Delayed Shut Down and charcoal filter buttons at the same time. ^ Store the selection by pressing the charcoal filter button. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. 16 Cleaning and Care Before cleaning or servicing the hood, disconnect it from the power supply by either removing the fuse, unplugging it from the outlet, or manually "tripping" the circuit breaker. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can be applied. Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly. Do not use a stainless steel cleaner on these controls. Cleaning the casing Warning: Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. ^ All external surfaces and controls can be cleaned with warm water and liquid dish soap applied with a soft sponge. Do not use too much water when cleaning the controls. Water could penetrate the electronics and cause damage. ^ Glass surfaces can be cleaned using a glass cleaner. Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents e. g. powder or cream cleansers, ­ abrasive sponges, e. g. pot scourers or sponges which have been previously used with abrasive cleaning agents, ­ limescale removers. These will damage the surface. 17 Cleaning and Care Grease filters The reusable metal grease filters remove solid particles from the vented kitchen air (grease, dust, etc). ^ In a dishwasher: place the filters vertically in the lower basket, making sure that the spray arm is not blocked. "Heavy Soil" or "Pots and pans". Use the recommended amount of dishwasher detergent. Depending on the detergent, cleaning the grease filters in a dishwasher may cause permanent discoloration of the filter surface. [. . . ] (820 - 1135 mm) To fit the chimney, the distance between the top of the chimney and the ceiling must be at least 7/8" (20 mm). 31 Installation Installation instructions ^ See the enclosed installation instruction sheet. ^ Please read the "Important Safety Instructions" and Installation instructions before installing this hood. Dismantling If the hood needs to be disassembled, follow the instructions on the installation sheet in the reverse order. A lever is enclosed for easier removal of the chimney extension. Protective film The casing is covered with a protective film to prevent scratching during transport. ^ Peel off the film before installing the casing parts. ^ After removing the screws from the chimney, slide the lever between the chimney and the chimney extension and gently apply pressure to ease the chimney from its hooks. 32 Air extraction , WARNING Danger of toxic fumes. [. . . ]