User manual MIELE DA 92

[. . . ] The manufacturer cannot be held responsible for damages caused by improper use of the hood. This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage. READ AND SAVE THESE INSTRUCTIONS cooking smoke and odors only. ~ Be certain your appliance is properly installed and grounded by a qualified technician. [. . . ] The grease filter indicator and one of the fan power indicators will flash. The fan power indicators show the programmed time: 1st indicator from the left = 20 hours 2nd indicator from the left = 30 hours 3rd indicator from the left = 40 hours 4th indicator from the left = 50 hours If the procedure is not stored within 4 minutes of programming the hood will automatically default to the "old" data. ^ Use the joystick to select the desired time. Press it to the left for a shorter operating time, to the right for a longer operating time. 14 Operation Reprogramming the charcoal filter timer The active charcoal filters can only be used in recirculation mode and cannot be used to exhaust fumes. The charcoal filter timer is not preset. Before using the hood in recirculation mode, the charcoal filter timer must be programmed. ^ Press the joystick to the left to turn the fan off. ^ Use the joystick to select the desired time. Press it to the left for a shorter operating time, to the right for a longer operating time. ^ Press the Delayed Shut Down and charcoal filter buttons at the same time. The indicator for the charcoal filter and one of the fan power scale indicators will flash. The indicators of the fan power scale show the programmed time: 1st indicator from the left = 120 hours 2nd indicator from the left= 180 hours 3rd indicator from the left = 240 hours 4th indicator from the left = unlimited ^ Store the selection by pressing the charcoal filter button. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. 15 Cleaning and care Stainless steel colored controls Before cleaning or servicing the hood, disconnect it from the power supply by either removing the fuse, unplugging it from the outlet or manually "tripping" the circuit breaker. ^ If the grease filters are cleaned before the grease filter timer has reached its maximum, press the grease filter button for 6 seconds to reset the counter to zero. 17 Cleaning and care Active charcoal filter DA 2280 uses 2 active charcoal filters DA 92 uses 4 active charcoal filters In recirculation mode active charcoal filters must be used in addition to the grease filters. The active charcoal filters will be replaced in the canopy above the grease filters. Replacement active charcoal filters can be ordered from Miele. ^ Remove the grease filters to access the charcoal filters. See "Cleaning and Care - Grease filters". ^ Insert the charcoal filters. Before using: ^ Program the charcoal filter timer, see "Operation / Reprogramming the charcoal filter timer". Replace the active charcoal filters when the charcoal filter indicator lights, at least every 6 months or when they no longer absorb odors efficiently. ^ After replacing the charcoal filters, press and hold the charcoal filter button for about 3 seconds to reset the charcoal filter timer. ^ If the charcoal filters are replaced before the timer has reached its maximum, the charcoal filter button should be pressed for 6 seconds to reset the counter to zero. 18 Cleaning and care Changing the light bulb Before changing the light bulb, disconnect the hood from the power supply by either removing the fuse, unplugging it, or manually "tripping" the circuit breaker. When in use halogen bulbs become extremely hot, and they can burn your hands. Do not attempt to change the bulbs until they have had sufficient time to cool down. Fingerprints or body oils deposited on the bulb will decrease the life of the bulb. Follow the bulb manufacturer's instructions. [. . . ] ^ Attach the lower part of the joystick to the extension with a spring washer. Turn the m-symbol to the front and screw in place with an allen wrench while using a wrench to hold the joystick base. ^ Insert the lower half of the desired joystick into the socket, loosely secure it in place with the included screw and spring washer. Make sure the respective screw for the desired joystick is used. ^ Turn the printed part of the joystick so that the m-symbol faces front. [. . . ]