User manual MIELE HG02

[. . . ] Installation instructions Dishwasher To prevent accidents and machine damage, read these instructions before installation or use. UV M. -Nr. 05 690 921 Contents IMPORTANT SAFETY INSTRUCTIONS . 3 INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ . Install the dishwasher under the countertop . [. . . ] Trim kits are not available for custom door panels. 19 Installation Maximum panel weight A custom door panel must not exceed the listed maximum weight. An overweight panel will distort the door springs causing the dishwasher door to fall when opened. G 600 door panel Plastic control 13 lbs panel (5. 9 kg) Stainless Steel 10. 5 lbs control panel (4. 8 kg) G 800 door panel 12 lbs (5. 5 kg) 9 lbs (4. 1 kg) 20 Installation ^ Place a template on each end of the mounting bracket as shown, making sure the rule marks face the outside of the bracket. ^ Slide the bracket up or down until the oblong holes on the machine door line up with the oblong holes on the template (shown in inset a). ^ Draw a line on each template that is even with the top edge of the adjacent cabinet door (inset b). ^ Place the door panel on a flat surface, good side facing down, taking care not to scratch the surface. Make certain that the bottom of the panel is closest to you. ^ Place the bracket on the back of the door panel and adjust it so that: ^ Hang the mounting bracket on the machine door. ^ Slide the top edge of the templates under the filler strips and control panel. ­ the lines drawn on the templates align with the upper edge of the door panel. ­ the mounting bracket is centered (left to right) on the door panel. 21 Installation ^ Tape the bracket to the door panel to hold it in place while the mounting holes are drilled. ^ Drill pilot holes for the screws using a 3 /32" (2. 5 mm) bit. ^ Attach the bracket to the panel using the 6 screws provided. Save the templates for future use in case a new door panel needs to be installed. 22 Installation ^ Push up one side of the door panel until it touches the filler strips (or control panel if filler strips are not used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door. ^ Repeat the process with the other side of the door panel. ^ Check that the door panel is adjusted correctly. It should be snug at the top and neatly aligned with the cabinet doors and drawer lines. If it is not aligned properly, loosen the Torx screws and adjust the panel. Once the door panel is positioned correctly: ^ Open the dishwasher door. ^ Tighten all the Torx screws on the edges of the dishwasher door. ^ Use the provided caps to plug the locking screw access holes. ^ Attach the panel to the dishwasher by aligning the bracket tabs with the slots on the door. ^ Open the dishwasher door slightly. If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches. 23 Installation If the adjacent cabinetry (or appliance) does not have drawers and alignment to a drawer line is not possible: ^ Hang the bracket on the machine door, without the templates. Tighten the four locking screws on the edges of the door panel. ^ Measure the distance from the adjacent cabinet's (or appliance) door bottom to the bottom of the mounting bracket (X). ^ Draw a line on the rear of the door panel (X) inches up from the bottom. ^ Remove the bracket from the machine door and place it on the rear of the door panel so that: ­ the bracket is centered left to right, ­ the bottom of the bracket is aligned with the (X) line. [. . . ] Do not cut the plug off the power supply cord and connect it directly to the house wiring. 34 Installation 13. Test the unit Once the dishwasher is level and secured it should be tested. ^ Remove all packing and literature from inside the unit. The yellow Child Safety Lock key hung on the upper basket must be removed before operating the dishwasher. [. . . ]