User manual MIELE KM 81-2

[. . . ] Operating instructions Gas cooktop KM 81-2 CANADIAN GAS ASSOCIATION R APROVED @]äö M. -Nr. 04 426 731 Description of the appliance Description of the appliance KM 81-2 2 Description of the appliance Description of the appliance KM 81-2 Data plate Because the data plate is no longer visible once the appliance has been built in, a 2nd data plate is supplied which should be placed into the space provided on page 16 of these instructions under After Sales Service. b Trivet c Wok/pan support d Small burner cap eLarge burner cap f Burner ring g Large burner cap base h Ignitor i Cable for connection to electrical supply approx. 3. 6 ft (1. 10 m) long. Special accessories Special accessories are available from your Miele Dealer or from the Spare Parts Department. Stainless steel cover-EA 80 A stainless steel cover is available for the KM 81-2 cooktop. [. . . ] When contacting the Service Department, please quote the Model and Serial No. of the appliance, both of which can be found on the data plate. Space for enclosed data plate 17 Electrical connection The automatic ignition requires connection to an a. c. Actual power consumption (during ignition only) is 25 W. These appliances are factory equipped with a power supply cord ready for connection to an electrically grounded socket which complies with your local electrical codes or with the: National Electical Code ANSI/NFPA No. 70-1481 for the USA or Canadian Electrical Code Part I for Canada. Ensure that the reeptacle is so positioned that it is easily accessible when the appliance is built in. ]öElectrical connection ]ö Technical data CDN / USA Total connected load . 25 W Electrical connection to 3 prong wall outlet: . 1. 1 m (3 ft) Check that data given on the data plate under the appliance complies with the main voltage. WARNING: THIS APPLIANCE MUST BE GROUNDED. Do not cut or remove the grounding prong from this plug. 18 Electrical connection Electrical connection AUS Electrical connection of the appliance should be undertaken by a suitably competent person in strict accordance with national and local safety regulations. For extra safety it is advisable to install a residual current device (RCD), with a trip current of 30 mA. The appliances are supplied with a mains cable for connection to single phase 240 V, 50 Hz supply. The plug rating and rated load are given on the data plate. Connection should be made by a switched socket. The On-Off switch should be easily accessible after the appliance has been built-in. Electrical connection NZ The appliances are supplied with a mains cable for connection to single phase 230 V, 50 Hz supply. The plug rating and rated load are given on the data plate. Important: The wires in the mains lead are coloured in accordance with the following code: Green/yellow = earth Blue = neutral Brown = live @ä @äElectrical connection As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol z or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter A or coloured red. WARNING THIS APPLIANCE MUST BE EARTHED. Technical data AUS (NZ) Total connected load . 1. 10 m If the connection cable needs replacing, only use cable with at least 3 x 1 mm2. 19 ]ö Gas connection ]ö Gas connection This appliance must be installed with a separate shut-off valve and a gas pressure regulator. [. . . ] Pull the controls for the gas burner up and off. Carefully raise the cooktop cover slightly at the rear and pull forward. Then carefully lift upwards and forwards. Ensure that the earth lead which connects the cooktop and the control panel is not damaged. 37 @ä Conversion to alternative types of gas @ä Conversion to alternative types of gas Changing the small jets Natural gas Liquid gas The jets must be changed: Changing the main jet, (does not apply to conversion to Natural Gas). [. . . ]