User manual MIELE KM 83-2

[. . . ] Operating instructions for Gas cooktops KM 83-2, KM 93-2 CANADIAN GAS ASSOCIATION R APROVED ]ö M. -Nr. 03 998 090 Description of the appliance Description of the appliance KM 83-2 5 4 3 6 7 2 8 9 1 10 12 1 1 KM 93-2 4 3 5 6 7 8 2 1 9 10 11 2 15 14 13 12 Description of the appliance Description of the appliance KM 83-2 b Control panel c Normal burner n Control for the rear right burner o Control for the rear left burner p Control for the front left burner dFast burner e Pan support f Ring support for the Normal burner g Burner cap h Ignitor i Ignition safety control j Burner head k Cable for connection to electrical supply approx. Data plate Because the data plate is no longer visible once the appliance has been installed, a 2nd data plate is supplied which should be placed into the space provided on page 15 of these instructions. Special accessories Special accessories are available from your Miele Dealer or from the Miele Parts Department. [. . . ] Turn the control knob to a low setting to prevent food from boiling over or burning. To shut the burner off, turn the control knob clockwise to the "X" position. The flame will go out. Power outage If there is an interruption to the electrical supply, the gas can be ignited with a match. Press in and turn the burner control counter-clockwise to the highest setting, (large flame). With the control knob pressed in, ignite the gas at the burner with a match. Wide, flat pans are more suitable than narrow, tall ones, since they heat up more quickly. Lids Less heat is lost by cooking in a covered pot. 12 Cleaning and care Cleaning and care If of a pot boils over, clean the burner and the cooktop surface immediately, to prevent the substance from burning on. Burners The burners can be dismantled for cleaning when cold. Burner caps The burner caps can be cleaned with a solution of dishwashing liquid. Do not use any caustic cleaners, scouring powders, knives or hard brushes, as these will scratch. With time and use, the surface of the burner caps will attain a matt finish. Burner head These can be cleaned with a damp cloth or with a chrome / stainless steel cleaner. Electronic ignition The ignitors must always be dry, otherwise they will not spark. From time to time, the ignitors should be wiped with a damp cloth and dried with a clean cloth. Install the burner cap correctly on the burner head after cleaning. Important: The burners must be correctly installed before they are lit, otherwise the ignitor could be damaged. Pan supports, ring support Caution: the pan supports and the ring support become hot during use. The pan supports can be removed for cleaning: Lift the support at the back and pull it out of the holders at the front. 13 Cleaning and care Cleaning and care The pan supports and ring support can be cleaned in a hot solution of dishwashing liquid. Never use scouring agents as these could scratch the surface. Cooktop surface Do not allow liquids or foods containing salt or sugar to spill onto the cooktop. Should this happen, wipe up any spills immediately, otherwise discoloration could occur. Remove dust, oils and fats, spills of foods and condensed water from pots and pans immediately to prevent them from drying on. Dried on food residues are easier to remove if they are first softened with warm water. Clean the cooktop surface using hot water with a little dishwashing liquid. [. . . ] It is supplied with its own installation instructions. 19-5/16" 56-9/16" 19-5/16" 56-1/2" 19-5/16" 68-1/16" Place the seal provided f under the edge of the cooktop. 23 Conversion to alternative types of gas Conversion to alternative types of gas When converting to alternative types of gas, the main and small jets of all burners must be changed. Select the new jets following the table below. The gas cooktop is supplied equipped for natural gas; the appropriate gas jet kit for propane gas, LPG, is also supplied with the appliance. Reference table - jet sizes Main jet diameter Natural gas Normal burner Fast burner LP gas Normal burner Fast burner 1. 22 mm 0. 048" 1. 55 mm 0. 061" 0. 72 mm 0. 028" 0. 91 mm 0. 036" Small jet diameter 0. 48 mm 0. 019" 0. 57 mm 0. 023" 0. 32 mm 0. 013" 0. 40 mm 0. 016" Conversion to LP Gas Turn off the main gas supply (if the appliance has already been installed) and turn off the main electrical supply. [. . . ]