User manual MIELE T 1303

[. . . ] Operating Instructions Vented Dryer T 1303 To prevent accidents and machine damage, read these instructions before Installation or use. UV M. -Nr. 05 863 591 Contents IMPORTANT SAFETY INSTRUCTIONS . Turn on the dryer and load the laundry . 12 Adding or removing laundry during a program . [. . . ] The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is ^ Restore power. securely closed to prevent a short circuit or penetrating moisture. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^ Flip down the bulb cover. 16 Frequently asked questions What if the dryer will not run? Possible fault Fix The "Start/Stop T" button was not pressed. The circuit breaker tripped or the dryer is unplugged. How do I prevent static cling? Make sure the dryer is on. Press the "Start/ Stop T" button to begin the drying program. Make sure the dryer is plugged in or reset the circuit breaker. Close the door properly. Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. What if the drum light does not come on? Possible fault Fix The bulb may be bad or burned out. See "Changing the light bulb. " What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started? Possible fault Fix The child lock is activated. Deactivate the child lock. See "Child Lock. " What if the program stops, the "Anti-crease / End" indicator lights and the buzzer sounds? Possible fault Fix The drum is empty. Load laundry into the dryer. The dryer will not operate when the drum is empty. Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff" program. What if the "Filter/Vent" fault indicator is lit? Possible fault Fix The lint filter is clogged. The exhaust hose or the connection is clogged with lint. The air supply in the room is insufficient. Clean the lint filters. Remove lint and check the exhaust system for blockages. Open a window or door to increase airflow. 17 Frequently asked questions What if the "Filter/Vent" indicator lights after cleaning the exhaust system? Possible fault Fix The dryer is not operating efficiently because the duct hose is too long. Check the exhaust length and diameter (see "How to calculate the effective duct length"). A long exhaust hose will increase program times and energy consumption. If the exhaust hose cannot be shortened, the indicator can be turned off by a service technician. What if the program runs too long or stops? Possible fault Fix The airflow is insufficient in the area of the dryer. The lint filters are clogged. Open a window or door to increase airflow. Clean the lint filters (see "Dryer care"). The laundry was not spun sufficiently in Select a higher spin speed in the wash the washer. Metal zippers interfere with the dryer's moisture sensors. Select a timed program to avoid overdrying. An airflow gap of 3/8" (10 mm) must be This gap must not be blocked by a provided between the machine and the toekick or thick piled carpets for sufficient airflow. What if the laundry is not dry enough? Possible fault The load contained too many dissimilar items (size and fabric. ) What if water has collected around the drum opening? Possible fault This is condensed moisture from the laundry. 18 Quick Guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the dryer. Quick Guide 1. Turn on the dryer and load the laundry 2. [. . . ] Necessary materials: ­ a wall or window duct ­ an exhaust hose made of approved non-flammable material Window connection 1 Window connection (installed in a plexiglass pane) 2 Connector for the flexible exhaust hose Wall connection with rigid pipe ^ If the duct length is more than 33 ft (10 m), remove the ring adapter, 1, from the connector, 2. If the duct length is less than 33 ft (10 m), leave the ring adapter in to improve time and energy efficiency. ^ Install the connector, 2, with the exhaust hose or pipe, 3, to the dryer. 1 Wall pipe 2 Connector 3 Rigid pipe 30 Installation Direct wall connection Necessary materials: ­ a wall pipe ­ flexible foam gasket Dryer top view Dryer side view 1 Wall pipe 2 Flexible foam gasket 1 Wall pipe 2 Flexible foam gasket ^ Insert the ring adapter, 1, into the wall pipe. Connect the flexible foam gasket, 3, to the wall pipe connector, 2. [. . . ]