User manual MIELE T1403-VENTED DRYER

[. . . ] Operating Instructions Vented Dryer T 1403 To prevent accidents and machine damage, read these instructions before Installation or use. UV M. -Nr. 05 313 341 Contents IMPORTANT SAFETY INSTRUCTIONS . Turn on the dryer and load the laundry . 12 Adding or removing laundry during a program . [. . . ] ^ Wipe dry. Cleaning the drum ^ The stainless steel surfaces of the drum can be cleaned using a non-abrasive stainless steel cleaner. ^ Wipe clean with a soft cloth. 15 Dryer care Changing the light bulb ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place. , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is ^ Restore power. securely closed to prevent a short circuit or penetrating moisture. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^ Flip down the bulb cover. 16 Frequently asked questions What if the dryer will not run? Possible fault Fix The "Start/Stop T" button was not pressed. The circuit breaker tripped or the dryer is unplugged. How do I prevent static cling? Make sure the dryer is on. Press the "Start/ Stop T" button to begin the drying program. Make sure the dryer is plugged in or reset the circuit breaker. Close the door properly. Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. What if the drum light does not come on? Possible fault Fix The bulb may be bad or burned out. See "Changing the light bulb. " What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started? Possible fault Fix The child lock is activated. Deactivate the child lock. See "Child Lock. " What if the program stops, the "Anti-crease / End" indicator lights and the buzzer sounds? Possible fault Fix The drum is empty. Load laundry into the dryer. The dryer will not operate when the drum is empty. Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff" program. What if the "Filter/Vent" fault indicator is lit? Possible fault Fix The lint filter is clogged. The exhaust hose or the connection is clogged with lint. The air supply in the room is insufficient. Clean the lint filters. Remove lint and check the exhaust system for blockages. Open a window or door to increase airflow. 17 Frequently asked questions What if the "Filter/Vent" indicator lights after cleaning the exhaust system? Possible fault Fix The dryer is not operating efficiently because the duct hose is too long. Check the exhaust length and diameter (see "How to calculate the effective duct length"). A long exhaust hose will increase program times and energy consumption. If the exhaust hose cannot be shortened, the indicator can be turned off by a service technician. What if the program runs too long or stops? Possible fault Fix The airflow is insufficient in the area of the dryer. The lint filters are clogged. Open a window or door to increase airflow. [. . . ] Changing the position of the exhaust connection ^ Remove the exhaust connection cover on the left or right side of the dryer. The dryer must be level to ensure safe and proper operation. Minor discrepancies do not however, have an adverse effect on operation. ^ Turn the cover counterclockwise to remove it. ^ Firmly press the cover into the rear opening. The machine can be leveled by turning the legs clockwise or counterclockwise as necessary. 27 Installation Installation tips An airflow gap of 3/8" (10 mm) must be provided between the machine and the floor. This airflow gap must not be blocked by a toekick or thick piled carpets. [. . . ]